TM 11-6625-3145-14
Introduction & Specifications-318/338 Service
Table 1-1 (cont.)
318/338 ELECTRICAL SPECIFICATIONS
Performance
Supplemental
Characteristics
Requirements
Information
Trigger position
In delay mode, the trigger posi-
Begin
word 7
tion is assigned by the user as
Center
word 127
follows:
End
word 247
Trigger position = (250 - delay
Delay
word 250 (when delay value is set to 0)
value).
Trigger position accuracy
±
1 clock
External trigger only.
Trigger mode
Immediately (first trigger) or After Memory
If instrument does not complete
Full
full memory acquisition before
the end of store, a fraction of
the display is indicated as "inva-
lid" data on data display.
Trigger output
Initiated high when an internal trigger se-
quence, glitch trigger, or external trigger was
detected. Reset on next acquisition start.
Output level
TTL
0.7 V or less for low level
output.
Voltage, maximum
+6 V
2.4 V or more for high level
output.
Current, maximum
High-logic level
-1 mA
Low-logic level
2 mA
Typical propagation delay
60 ns after the trigger event is clocked and
detected with internal clock.
80 ns after the trigger event is clocked and
Measured from external clock
detected with external clock.
input to trigger output.
±
1 clock interval when external trigger is
Measured from external trigger
used.
input to trigger output.
Qualifier
Input
9th channel of each P6451 probe is used as
For more information, refer to
a qualifier input.
P6451 literature.
Input R and C
1 M
Ω
± 5%, paralleled by approx. 5 pF
(without leads).
Minimum logic swing
500 mV p-p centered on threshold voltage.
1-7
Summary of Contents for 318
