TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
The CRT test generates the following types of patterns for the CRT adjustment and visual check.
•
Cross-hatch pattern (Figure 5-5). Used to adjust the CRT circuit.
•
White pattern (Figure 5-6). Used to check for phosphor defects.
•
All character fonts for Parallel Analyzer mode (Figure 5-7). Used to check the CRT circuit and the CROM
(character ROM) for parallel analyzer operations.
•
All character fonts for Serial Analyzer mode (Figure 5-8). Used to check the CRT circuit and the CROM for serial
analyzer operations.
3.
Press the X key to return to the Diagnostic menu.
CHECK 4. THRESHOLD VOLTAGE
1.
Connect all the data and ground leads of the P6451 Parallel Data probes in both Pod A and Pod B together and
connect them to the instrument ground.
2.
Press the THRESHOLD menu key (normal operating mode).
Threshold Level TTL
a. Set INPUT Thresholds to TTL for for both Pod A and Pod B.
b. Press the START key. The trigger position (indicated by T) will be displayed on the screen. The trigger position
will be <T=7W>, <T= 127W>, or <T=247W> depending on the trigger position setting in the Trigger menu (begin,
center, or end).
c. Check that all data acquired are O's.
Threshold Level V1
a. Set Threshold LEVEL V1 to +0.3 V.
b. Set both Pod A and Pod B equal to V1.
c. Press the START key. The trigger position displayed on the screen will be <T=7W>, <T=127W>, or <T=247W>
depending on the trigger position setting in the Trigger menu.
d. Check that all data acquired are O's.
e. Set Threshold LEVEL V1 to -0.3 V.
f. Press the START key. The trigger position displayed on the screen will be <T=7W>, <T=127W>, or <T=247W>
depending on the trigger position setting in the Trigger menu.
g. Check that all data acquired are 1's.
5-9
Summary of Contents for 318
