TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
INPUT
EXT CLK =
V3
POD A =
V3
POD B =
V3
POD C =
V3
POD D =
V3
TRIGGER MENU
Source
INT TRIG
CLK
EXT
TRIG
IMMEDIATELY
POSN
DELAY
00249
Events
00001*WA FLW’D BY:WB OFF WC
WA =
XX
WB =
XX
WC =
GLITCH
76543210
POD A
OFF
QUALIFIERS (POD)
A OFF
B OFF
C OFF
D OFF
10.
Set the oscilloscope as shown in Table 5-20.
11.
Set the Pulse Generators as shown in Table 5-21.
NOTE
Over adjustment of the EVENTS LEVEL will cause a loss of the DD501 triggering
and oscilloscope display. If the adjustment range is not adequate then replace the
BNC cables, between the Pulse Generators and the Digital Delay, with longer or
shorter cables.
12.
Set the oscilloscope triggering source to CH2 ONLY.
13.
Adjust DD501 EVENTS LEVEL slowly until the channel 2 waveform’s falling edge crosses the channel 1 waveform’s
rising edge at 0 V (mid-screen). See Figure 5-60 (20 ns setup, 0 ns hold).
NOTE
Over adjustment of the EVENTS LEVEL will cause a loss of the DD501 triggering
and oscilloscope display. If the adjustment range is not adequate replace the 42
inch BNC cable, from DLY’D TRIG OUT to the #2 Pulse Generator’s + TRIG INPUT,
with a longer or shorter cable, or remove the cable’s 50
Ω
terminator.
14.
Setup the 338 CLK and QUALIFIERS for Condition 1 in Table 5-22.
15.
Press the 338 DATA key until the State Table is displayed.
16.
Press the START key.
17.
Check that the data acquired is equal to the Expected Data in Table 5-22.
18.
Setup the 338 CLK and QUALIFIERS for conditions 2 through 4 in Table 5-22. Repeat steps 14 to 16 for each
condition.
5-104
Summary of Contents for 318
