TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
e. Select the Threshold menu and set LEVEL V1 = 0.0 V, and V2 = 0.0 V.
f. Set INPUT DATA = V1.
g. Press the START key.
h. Set the oscilloscope controls so that channel 1 and channel 2 waveforms are superimposed.
i. Adjust C10 (COMPENSATION) on the A07 board so that the shape of the channel 1 waveform most nearly
matches the shape of the channel 2 waveform.
j. Press the STOP key.
k. Remove 40 pF normalizer from SERIAL DATA INPUT and from the BNC T-connector.
I. Connect P6107 Serial Data Probe from the SERIAL DATA INPUT jack to the male end of the BNC T-connector.
m. Adjust the oscilloscope controls so that the channel 1 and channel 2 waveforms are superimposed.
n. Remove the P6107 Serial Data Probe CALIB SEAL.
o. Adjust P6107 Probe compensation screw so that the waveform corners are square.
p. Reinstall the CALIB SEAL.
q. Disconnect the test probes.
11. Adjust Non-volatile Memory Battery Backup Threshold
Equipment Required
1.
Oscilloscope
1.
Digital Multimeter (DMM)
Refer to Figures 5-16 and 5-17.
a. Connect the DMM minus (-) lead to TP200 (GND) on the A07 board.
b. Connect the DMM plus (+) lead to TP101 (+5 V) on the A07 board.
c. Record the voltage measured.
d. 5V POTENTIOMETER R11 on the A12 REGULATOR board for a DMM indication of 4.65 + 0.01 V.
e. Connect the oscilloscope channel 1 probe tip to TP100 on the A07 board.
f. Set the oscilloscope to 1
µ
s/div. and 2 V/div., dc.
g. Turn NVM THRESHOLD R101 on the A07 board clockwise until the oscilloscope indication is low.
h. Adjust NVM THRESHOLD R101 by slowly turning counterclockwise until the oscilloscope waveform level rises
to high.
h. 5V POTENTIOMETER R11 on the A12 REGULATOR board for a DMM indication equal to that
recorded in step (c) above.
5-41
Summary of Contents for 318
