TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
2. Pod A
a.
Press the START key and wait for the acquisition to be completed.
b.
Check that all the data for Pod A is displayed in inverse video in the GLITCH SEARCH mode, and that <T
=0
♦
> is showing in the lower-right corner of the screen.
c.
De-select Trigger Glitch A7.
d.
Repeat steps (a) through (c) for each of the remaining channels, A6 through A0. Glitch Triggering must be
checked one channel at a time for the test to be valid.
3. Pod B
a.
Disconnect the 10-terminal plug from the probe head of the P6451 Parallel Data probe in Pod A.
b.
Push the 10-terminal plug into the socket on the probe head of the P6451 Parallel Data probe in Pod B.
c.
Set G1 to OFF and G2 to ON for B7 - B0.
d.
Set GLITCH Pod A to OFF and Pod B to ON for B7.
e.
Press the START key and wait for the acquisition to be completed.
f.
Check that all the data for Pod B is displayed in inverse video in the GLITCH SEARCH mode, and that <T =
0
♦
> appears in the lower-right corner of the screen.
g.
Repeat procedures (e) through (f) for channels B6 through B0 of the Pod B GLITCH Trigger. Glitch
Triggering must be checked one channel at a time for the test to be valid.
CHECK 7. SERIAL STATE ANALYZER CHECK FOR THE 318S1
1. Serial Data Acquisition
a.
Connect the test setup as shown in Figure 5-12.
b.
Set the terminal character format to 8 bits per character.
c.
Set the 318 POWER switch to ON and press the SETUP key after the diagnostic program has run.
d.
Set the major mode to SERIAL and press the EXECUTE key.
e.
Set the baud rate and parity to match that of the terminal. Press the THRESHOLD Menu key.
f.
Set the data threshold to 0.00 V. Press the TRIGGER Menu key.
g.
Set the trigger mode to IMMEDIATELY. Press the DATA key.
h.
Press the START key.
i.
Press the A key on the terminal keyboard 10 times.
j.
Press the STOP key.
k.
Check that the acquired data equals 10 bytes of ASCII A on the screen.
5-19
Summary of Contents for 318
