TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
TEST 5 - EXTERNAL TRIGGER INPUT
Equipment Required
1 BNC to Mini-Jack Cable, 175-1178-00
1 Oscilloscope
1 Pulse Generator
1 10X Probe
1 BNC-to-Probe Adapter
1 50 ohm Terminator
1.
Connect a 50 ohm terminator to the pulse generator OUTPUT.
2.
Connect a 10 OX probe from the oscilloscope CH1 to the 50 12 terminator at the pulse generator OUTPUT using a
BNC-to-probe Adapter.
3.
Setup the oscilloscope as follows:
TRIGGERING
AUTO, AC, INT, CH1
TIME/DIV
5 ns (Use 10OX Magnifier if necessary)
CH1 VOLTS/DIV
1.0 V DC
CH1 POSITION
0 V (GND) set to the middle of screen
4.
Set the pulse generator as follows:
BACK TERM
OUT
OUTPUT
NORM
PERIOD
.1
µ
S
HIGH LEVEL
+2.80 V
LOW LEVEL
0.00 V
DURATION
20 nS @ +-1.4 V level
5.
Remove the 10X Probe and BNC-to-probe adapter from the pulse generator.
6.
Connect a BNC-to Mini-jack Cable from the 50 ohm terminator at the pulse generator’s OUTPUT to the TRIG INPUT
mini-jack on the right-side panel. Connect the cable braid lead to the GND mini-jack, also on the right-side panel.
7.
Power-up and setup the as follows:
TRIGGER MENU
SOURCE EXT
TRIG
EXT TRIG POL=
↑
8.
Press the START key and check that the 338 triggers.
9.
Set pulse generator PERIOD to EXT TRIG and ensure no cables are connected to the pulse generator External
Trigger Input.
10.
Press the START key and then press the pulse generator’s MAN TRIG.
11.
Check that the 338 triggers only after the PG502 MAN TRIG button is pushed.
12.
Set EXT TRIG POL to negative and the pulse generator’s OUTPUT to COMPLEMENT.
13.
Repeat steps (10) and (11).
5-116
Summary of Contents for 318
