TM 11-6625-3145-14
Maintenance: Troubleshooting-318/338 Service
I/O ADDRESS
=
8C
CHIP
=
RESET TO U31
FUNCTION
=
SERIAL PARAMETER SETUP REGISTER
CONTROL
=
WRITE ONLY
bit =
7
6
5
4
3
2
1
0
baud
baud
baud
baud
extern.
Serial
select
select
select
select
trigger
data
xxxxx
xxxxx
as S3
as S2
as S1
as S0
pol.
pol.
NOTE: xxxxx data bits have no function.
bit 7, 6, 5, 4: these four bits are used to set serial baud rate. S3, S2, S1, SO select the baud rate by
same manner shown in RS-232 BAUD RATE SETUP REGISTER.
bit 3: ON
=
set external trigger direction to trailing edge.
OFF
=
set external trigger direction to leading edge.
bit 2
ON
=
set serial input data polarity to negative.
OFF
=
set serial input date polarity to positive.
I/O ADDRESS
=
90
CHIP
=
U2
FUNCTION
=
READ DATA OF SERIAL PORT
CONTROL
=
READ
I/O ADDRESS
=
91
CHIP
=
U2
FUNCTION
=
SERIAL DATA ACQUISITION CONTROL
CONTROL
=
READ AND WRITE
I/O ADDRESS
=
92
CHIP
=
U2
FUNCTION
=
READ AND WRITE DATA OF RS-232 PORT
CONTROL
=
READ AND WRITE
I/O ADDRESS
=
93
CHIP
=
U2
FUNCTION
RS-232 MODEM SIGNAL AND DATA CONTROL
CONTROL =
READ AND WRITE
The SIO chip U2 has these four I/O address registers: Address 90 and 91 are SIO Port-A registers, and 92 and 93 are SIO
Port-B registers. Control addresses 91 and 93 include three READ only and eight WRITE only internal registers. These
internal registers control and check all SIO functions.
Details of the SIO internal register functions are described in the
Z80 SIO MANUAL
by ZILOG, SHARP, MOSTEK.
7-128
Summary of Contents for 318
