TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
13. Adjust the corresponding jumper to place the rising or falling edge (indicated by
↑
or
↓
in Table 5-16) of the
channel 2 waveform within one division of the graticule centered on the rising edge of the channel 1
waveform.
14. Press the STOP key.
15. Turn off the 338.
16. Dismount the A03 ACQ Control board and the A04 ACQ Memory board from the Extender boards.
17.
Remove the Extender boards from slots A03 and A04.
18. Install the A03 ACQ Control board and the A04 ACQ Memory board into slots A03 and A04 respectively.
19. Turn on the 338.
Table 5-16
338 CLOCK DELAY WITH EXTENDER
Delay
Clock
Ch 2 Edge
(ns)
Test Point
Jumper
RET CLK
↑
47.60 + 1.00
TP400 (A03)
J200(A03)
WE
↓
55.40 + 1.00
TP200-2(A04)
J300(A03)
TRIG CLK
↑
68.10 1.00
TP500 (A03)
J400(A03)
Capacitor Adjustment
1. Refer to Figures 5-52 and 5-53. Set EXT CLK Threshold to V3 (0.00 V).
2. Set CLK to EXT
↑
.
3. Set the Events field to: 00000*WA OFF:WB OFF:WC. This will cause the 338 to acquire data without
triggering.
4. Press the START key.
5. Repeat the following procedures, (6) through (8), to adjust each clock delay and/or width as shown in Table 5-
6. Connect the oscilloscope channel 2 probe tip to the corresponding test point given in Table 5-17.
7. Turn delta-TIME clockwise to obtain the delta-T reading of the clock delay being adjusted in Table 5-17.
8. Adjust the corresponding capacitor to place the rising or falling edge (indicated by a
↑
or
↓
in Table 5-17) of the
channel 2 waveform within one division of the graticule centered on the rising edge of the channel 1
waveform.
9. Press the STOP key.
10. Remove the oscilloscope test leads from the test points.
5-92
Summary of Contents for 318
