TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
5. Set the pulse generator as follows:
Termination BACK
TERM
(pull switch out)
Period
0.1
µ
s
Duration
10 ns (5 ns X 2)
High level
+0.35 V
Low level
-0.35 V
6. Select the A timebase and place the rising edge of the channel 1 waveform on the center graticule on the
oscilloscope screen.
7. Select the B timebase.
8. Turn DELAY TIME of the A timebase to place the rising edge of the channel 1 waveform on the center graticule.
B. Strap adjustment with Extender boards (Optional Maintenance Kit Required)
1. Turn off the 318.
2. Remove the A03 ACQ CONTROL board and the A04 ACQ MEMORY board using the Board ejectors.
3. Install Extender boards into the J03 and J04 connectors.
4. Mount the A03 ACQ CONTROL board and the A04 ACQ MEMORY board on the top of the Extender boards.
5. Turn on the 318.
6. Select the Threshold menu and set INPUT EXT CLK = V3 (0.00 V).
7. Set CLK to EXTT.
8. Select the Trigger menu and set the Events field to: 00000*WA OFF:WB OFF:WC. This will cause the 318 to
acquire data without triggering.
9. Press the START key.
10. Repeat the following procedures, (11) through (13), to adjust each clock delay with Extender boards shown in
11. Connect the oscilloscope channel 2 probe tip to the corresponding test point given in Table 5-5.
12. Turn
∆
-TIME clockwise to display the clock delay value listed in Table 5-5.
13. Adjust the corresponding jumper to place the rising or falling edge (indicated by
↑
or
↓
in Table 5-5) of the channel
2 waveform within one graticule division of the rising edge of the channel 1 waveform.
14. Press the STOP key.
15. Turn off the 318.
16. Dismount the A03 ACQ CONTROL board and the A04 ACQ MEMORY board from the Extender boards.
17. Remove the Extender boards from slots A03 and A04.
18. Install the A03 ACQ CONTROL board and the A04 ACQ MEMORY board into slots A03 and A04 respectively.
19. Turn on the 318.
5-36
Summary of Contents for 318
