TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
Table 5-2.
MINIMUM SPECIFICATIONS FOR TEST EQUIPMENT
Equipment
Specification
Tektronix Equivalent Instrument
Two-channel oscil-
175 MHz
7904 (mainframe) with 7A26 (200 MHz dual
loscope with 1-meter
trace amplifier), 7B80 (1 ns/div delayed time-
probes
base), 7B85 (
∆
delayed timebase), and P6106 probes
Pulse generator
250 MHz pulse rate,
PG502
variable output
levels
Digital delay
DD501
Digital multimeter
4.5 digits, 0.05% dc
DM501
volts accuracy
Regulated dc power supply
PS501
Power module (optional)
TM506
Serial data generator
performance and features
834
equal to Tektronix 834
Computer terminal
4025
FUNCTIONAL CHECK PROCEDURES FOR THE 318
The following procedures are for the 318 Logic Analyzer only. The Functional Check for the 338 Logic Analyzer begins in
the second half of this section; refer to the margin tabs for help in locating the 338 procedures.
The Functional Check Procedure verifies that all major sections of the logic analyzer are operational. These tests can be
used to determine whether adjustment and/or repair is necessary. The procedures are organized into sets of tests for the
mainframe, the acquisition module, each type of probe, and the 318S1 serial acquisition and communication option.
Refer to the beginning of this
Verification and Adjustment Procedures
section, and to the
Operating Information
section, for
instructions on probe connections and use of menus.
NOTE
These procedures assume that the user has a moderate understanding of the
operation of the 318 menus and hardware. Power-up of the 318 will preset menu
selections,’ power-up must be performed when so instructed.
5-6
Summary of Contents for 318
