TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
7.
Set the serial data generator power to ON, and select DTE SIMULATE mode.
8.
Set serial data generator SETUP as follows;
CODE=ASCII, BAUD=2400, DUPLEX-FULL, SETUP=ASYNC, BITS/CHAR=8,
PARITY= NONE, STOPBITS = 1, TIMING = NORMAL.
9.
Load the following program into the serial data generator:
STEP
MNEMONIC
CODE
1
SEND
#1
2
JMP
#1
10.
Load the following hexadecimal data in the serial data generaotor buffuffer #1: E0, E0, E2, E4, E6, E8
11.
Press the START key on the serial data generator.
12.
Select the DATA DISPLAY STATE TABLE and press the START key.
13.
When the 338 displays data on the crt, press the serial data generator STOP key.
14.
Check that the 338 display matches the WORD SEQUENCE column on Table 5-25.
15.
Set the 338 baud rate to 19.2K (DATA screen).
16.
Set the serial data generator baud rate to 19.2K.
17.
Set the 338 and the serial data generator controls as indicated in step 1 of Table 5-25 and repeat preceding parts
(11) through (14).
Repeat steps 2 through 7 for the remainder of Table 5-25.
NOTE
Selection field for BITS/’WORD and COM.MODE (SYNC or ASYNC) and BAUD RATE
appear in the 338 SETUP Menu. Selection fields for SYNC WORD and HUNT WORD
are in the TRIGGER Menu.
To load SETUP parameters into the serial data generator, the operator must: (a) press SETUP, (b) select SETUP item
using LEFT or RIGHT Vector keys. (c) select SETUP parameters using UP or DOWN VECTOR key.
To load data into the serial data generator buffer #1, the operator must: (a) press PROGRAM, (b) press RIGHT VECTOR,
(c) press DOWN VECTOR, (d) press keys for the two hexadecimal characters to be entered, and (e) press ENTER. To
load additional data , repeat parts (d) and (e).
To load the program into the serial data generator, the operator must: (a) press PROGRAM, (b) select program code by
LEFT or RIGHT VECTOR, (c) if program code includes distination number, press alphanumeric key to be entered, and
press ENTER, (d) press DOWN VECTOR, to next program step.
5-118
Summary of Contents for 318
