TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
LIMITS AND TOLERANCES
All limits and tolerances given in this procedure are adjustment guides. They should not be interpreted as
instrument specifications unless they are also found in the Specifications part of this manual.
Tolerances given are for the instrument under test and do not include test equipment error.
EQUIPMENT REQUIRED
The equipment, or equivalent, listed at the beginning of this Adjustment and Verification Procedures section in
Table 5-1, is necessary to complete all the adjustment procedures. A partial list of equipment needed for each
individual check and adjustment is also shown at the beginning of each procedure. The specifications given in
Table 5-2 are the minimum necessary to produce accurate results. Therefore, related equipment must meet or
exceed the listed specifications. Detailed instructions for operating the test equipment are not offered in this
manual. Refer to the manual for the specific piece of test equipment you are using if more information is required.
EQUIPMENT ALTERNATIVES
When equipment other than recommended test equipment is substituted, control settings or adjustment setups
may need to be altered. If the exact equipment listed in Table 5-1 is not available, check the Minimum
Specification column in Table 5-2 carefully to see if any other equipment will suffice.
ADJUSTMENT INTERVAL
To ensure correct instrument operation, adjustment should be checked every 1000 hours of operation or every six
months, if used infrequently. Before performing the adjustment procedures, perform preventive maintenance as
outlined in the Maintenance section.
TEST SEQUENCE
NOTE
These adjustment procedures assume prior knowledge of some aspects of
338 disassembly. If further information is required, refer to the disassembly
procedures in Section 6 Maintenance: General Information.
It is necessary to perform the following sequence step by step, because all timings are level-sensitive.
INDEX OF ADJUSTMENT STEPS
Mainframe
1. Power Supplies
2. CRT Circuit
3. Threshold Voltages on the A05 ROM Board
5-78
Summary of Contents for 318
