TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
A. Oscilloscope Setup
1. Install the modules into the 7904 oscilloscope main frame; 7A26 amplifier in the left vertical slot, 7B85 time base in
Horizontal slot A and 7B80 time base in Horizontal slot B.
2. Connect a 50
Ω
terminator to the pulse generator OUTPUT. Connect a BNC T-connector to the 50
Ω
terminator.
Connect the CH1 oscilloscope probe to one side of the BNC T-connector.
3. Connect the P6107 External Clock probe tip to the other side of the BNC T-connector.
4. Setup the oscilloscope as follows:
7904 Mainframe
Horizontal Mode B
7A26
Position
Rising edge at center screen
Channel 1
VOLTS/DIV
20 mv (200 mV with 10X probe)
Trigger Source
CH 1
Display Mode
ALT
Position
0 v at mid screen
Channel 2
VOLTS/DIV
50 mV (500 mV with 10X probe)
Position
0 v 2.4 divisions above midscreen (-1.4 V at midscreen)
7B85
Slope
+
Triggering
Mode Coupling Source
Auto AC INT
Magnification
1 X
Hold Off
at minimum
B Delay Mode
B Starts after DLY
Time/DIV
50 ns (5 ns with magnifiction)
Trace Sep
On, minimum
∆
Time
zero
7B80
slope
+
Triggering
Mode Coupling Source
Auto AC INT
Position
rising edge at center screen
Hold Off
at minimum
Time/Div
10 ns (1 ns with magnification)
5. Set the pulse generator as follows:
Termination
BACK TERM
(pull switch out)
Period
0.1
µ
s
Duration
10 ns (5 ns X 2)
High level
+0.35 V
Low level
- 0.35 V
6. Select the A timebase and place the rising edge of the channel 1 waveform on the center graticule on the
oscilloscope screen.
7. Select the B timebase.
8. Connect the oscilloscope channel 2 probe tip to TP108 on the A01 INPUT-A board.
9. Enter the Threshold menu and set EXT CLK to V3 (0.00V).
10. Select the TRIGGER Menu and set the events field to: 00000*WA OFF:WB OFF:WC. This will cause the 318 to
acquire data without triggering.
5-31
Summary of Contents for 318
