TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
0
##
(Always no data)
1
##
(Always no data)
2
##
(Always no data)
3
##
(Always no data)
4
##
(Always no data)
T
5
00 and/or FF
(Check several acquisitions)
(and make sure that both 00 and) (FF triggers occur.)
47. Press the STOP key and then the TRIGGER key.
48. Change the TRIGGER MENU as follows:
EVENTS
00002 ’ WA OFF:WB RESET ON:WC
WA = FF
WB
WC = 00
49. Press the START key and check that the 318 does not trigger.
50. Press the STOP key.
51. Change the TRIGGER MENU as follows:
POSN
DELAY = 00000
Events
00001 *WA OFF:WB RESET ON:WC
52. Press the DATA key, the T key (scroll), and then the START key.
53. Check for the following data and proper trigger location.
243
##
(Always no data)
244
##
(Always no data)
245
##
(Always no data)
246
##
(Always no data)
247
##
(Always no data)
248
##
(Always no data)
249
## or 00
T
250
FF
(Trigger location)
54. Press the STOP key and the the TRIGGER key.
55. Increase the DD501 DELAY COUNT by steps of 01000 until the oscilloscope display starts to become too dim to
observe.
56. Adjust the oscilloscope horizontal POSITION to display the channel 2 waveform.
57. Adjust the DD501 EVENTS LEVEL slowly until the channel 2 waveform’s falling edge crosses the channel 1
waveform’s rising edge at 0 V (mid-screen). See Figure 5-29 (14 nS setup, 0 nS hold).
NOTE
If adjustment range is not adequate then replace the DLY’D TRIG OUT BNC cable
with a longer or shorter one.
58. Set the DD501 DELAY COUNT to 65000.
59. Change the TRIGGER MENU as follows:
POSITION
DELAY = 65000
EVENTS
00001 * WA OFF:WB OFF:WC
WA = FF
5-53
Summary of Contents for 318
