TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
Table 5-4.
318 NON-ADJUSTABLE POWER SUPPLY TOLERANCES
J1 Pin Number
Voltage Limits
-12 V pin
-11.0 V to -13.0 V
+12 V pin
+11.0 V to +13.0 V
-2 V pin
-1.80 V to -2.20 V
2. Adjust CRT Circuit
Equipment Required
None
a.
Run the diagnostic program 1 CRT to generate a cross-hatch pattern. (To enter the diagnostic program,
turn on the power switch while depressing any numeric key until the display appears.)
b.
Refer to Figure 5-15. Adjust INTENSITY control R245 on the A10 CRT board to midrange.
c.
Adjust INTENSITY LIMIT (CRT BIAS) R247 on the A10 CRT board for normal intensity.
d.
Press the start key to display a horizontal line.
e.
Loosen the setting screw of L150 (yoke coil).
f.
Rotate the L150 so that the displayed white stripe is parallel to the bezel window.
g.
Tighten the setting screw of L150.
h.
Adjust MAGNET on L150 on the CRT ring to orient the display at approximately the center of the CRT.
i.
Adjust V-SIZE R015 on the A10 CRT board for vertical display size of about 2 mm less than the CRT
display.
j.
Adjust V-LINEARITY R031 on the A10 CRT board for optimum display.
Figure 5-15. 318 CRT adjustments.
5-25
Summary of Contents for 318
