TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
d. Setup the oscilloscope as follows:
7904 Mainframe
Horizontal Mode B
7A26
Position
Rising edge at center screen
Channel 1
VOLTS/DIV
20 mv (200 mv with 10 OX probe)
Trigger Source
CH 1
Display Mode
ALT
Position
0 v at mid screen
Channel 2
VOLTS/DIV
50 mv (500 mv with 10X probe)
Position
0 v 2.4 divisions above midscreen (-1.4 v at midscreen)
7B85
Slope
+
Triggering
Mode Coupling Source
Auto AC INT
Magnification
1 X
Hold Off
at minimum
B Delay Mode
B Starts after DLY
Time/DIV
50 ns (5 ns with magnifiction)
Trace Sep
On, minimum
∆
Time
zero
7B80
slope
+
Triggering
Mode Coupling Source
Auto AC INT
Position
rising edge at center screen
Hold Off
at minimum
∆
Time/Div
10 ns (1 ns with magnification)
e. Set the pulse generator as follows:
Termination
BACK TERM
(pull switch out)
Period
0.1
µ
s
Duration
10 ns (5 ns X 2)
High level
+0.35 V
Low level
-0.35 V
f. Select the A timebase and place the rising edge of the channel 1 waveform on the center graticule on the
oscilloscope screen.
g. Select the B timebase.
h. Turn DELAY TIME of the A timebase to place the rising edge of the channel 1 waveform on the center graticule.
i. Connect the oscilloscope channel 2 probe tip to TP106 on the A01 INPUT-A board.
j. Select the Threshold menu and set INPUT EXT CLK = V3.
k. Set CLK to EXT
↑
.
l. Select the Trigger menu and set the events field to 00000*WA OFF:WB OFF:WC. This will cause the 318 to
acquire data without triggering.
m.
Press the START key.
n. Turn A-TIME clockwise to obtain a reading of 43.00
±
0.1 ns.
o. Adjust DLD CLK DELAY by moving the jumper at J104 on the A01 INPUT-A board to place the rising edge of
the channel 2 waveform within one graticule division of the rising edge of the channel 1 waveform.
p. Press the STOP key.
5-34
Summary of Contents for 318
