TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
51.
Change the TRIGGER Menu as follows:
TRIGGER MENU
POSN
DELAY
00000
Events
00001’WA OFF:WB RESET ON:WC
52.
Press the DATA key,
←↑
T key (scroll), and then the START key.
53.
Check for the following data and proper trigger location.
243
##
(Always no data)
244
##
(Always no data)
245
##
(Always no data)
246
##
(Always no data)
247
##
(Always no data)
248
##
(Always no data)
249
##
or 00
T
250
FF
(Trigger location)
54.
Press the STOP key and then the TRIGGER Key.
a.
Increase the DD501 DELAY COUNT, by increments of 01000, until the oscilloscope display starts
becoming too dim to observe.
b.
Adjust the oscilloscope horizontal POSITION to display the channel 2 waveform.
c.
Adjust DD501 EVENTS LEVEL slowly until the channel 2 waveform’s falling edge crosses the channel 1
waveform’s rising edge at 0 V (mid-screen). See Figure 5-60 (14 ns setup, 0 ns hold).
NOTE
If adjustment range is not adequate then replace the DLY’D TRIG OUT BNC cable
with a longer or shorter cable.
55.
Set the DD501 DELAY COUNT to 65000.
56.
Change the TRIGGER Menu as follows:
TRIGGER MENU
POSN
DELAY
65000
Events
00001’WA OFF:WB OFF:WC
WA -
FF
WB
WC-
57.
Press the DATA key and then the START key.
58.
Check that data location 251 contains FF and all other data locations contain 00s. Note: The trigger location is off
the display screen.
59.
Press the STOP key and check the lower-right corner of the display for:
ST:T = -64750W
5-110
Summary of Contents for 318
