TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
5. Probe Compensation for the P6107 External Clock Probe
Equipment Required
None
If you are using a standard 318 Logic Analyzer you will have one P6107 probe labeled External Clock Probe. This probe
needs to be compensated to 20 pF according to the procedure described in Section 3:
Operating Instructions
. See the
Probe Compensation
paragraph in the Diagnostic Test Descriptions.
Two nearly identical P6107 probes are supplied with the 318S1 Logic Analyzers; one is the External Clock Probe, and the
other is the Serial Data Acquisition Probe. If the probes were supplied as original equipment, they will be labeled as either
EXT CLOCK, or SERIAL DATA with a sticker on the compensation box. The External Clock Probe is compensated to 20
pF, and the Serial Data Acquisition Probe is compensated to 40 pF.
If you have purchased replacement probes, or if you are adding the 318F1/338F1 Serial Analysis/RS-232C/NVM upgrade
kit to a standard 318, you need to choose which probe will be the External Clock Probe and adjust the compensation
accordingly. Probes supplied from the factory are compensated to 40 pF.
The P6107 Serial Data Acquisition Probe has been factory compensated (40 pF) and sealed with a CALIB. sticker.
Recompensation must be performed by qualified service personnel only. It is not necessary to compensate this probe.
We recommend that you install the colored marker band (supplied) on the probe for identification purposes.
If the P6107 External Clock Probe is a replacement the compensation must be altered. Remove and discard the CALIB.
sticker. Then perform the probe compensation procedure described in the
Operating Instructions
section (section 3) of
this manual. (See Probe Compensation under Diagnostic Test Descriptions.) We recommend that you install the colored
marker band (supplied) on the probe to help in identification.
6. Adjust EXT CLK
↑
and EXT CLK
↓
Delay
Equipment Required
1.
Oscilloscope Tektronix 7904 with plug in units 7A26, 7B80, and 7B85.
1.
Pulse Generator Tektronix PG502
1.
BNC 50
Ω
termination
1.
BNC T-connector
2.
BNC male to Probe tip Adapters
1.
2 SQR-pin to Probe tip Adapter
Figure 5-18. shows the test equipment setup for the Clock Delay adjustment.
Refer to Figures 5-18 and 5-19.
5-30
Summary of Contents for 318
