![Tektronix 318 Technical Manual Download Page 24](http://html1.mh-extra.com/html/tektronix/318/318_technical-manual_1077905024.webp)
TM 11-6625-3145-14
GROUNDING THE PRODUCT
This product is intended to operate from a power source that does not apply more than 250 volts rms between the
supply conductors or between either supply conductor and ground. This product is grounded through the
grounding conductor of the power cord. To avoid electrical shock, plug the power cord into a properly wired
receptacle before connecting to the product. A protective-ground connection by way of the grounding conductor in
the power cord is essential for safe operation.
DANGER ARISING FROM LOSS OF GROUND
Upon loss of the protective-ground connection, all accessible conductive parts (including knobs and controls that
may appear to be insulating) can render an electric shock.
USE THE PROPER POWER CORD
Use only the power cord and connector specified for your product, and be sure it is in good condition.
Refer to the
Operating Information
section of this manual for information on power cords and connectors.
USE THE PROPER FUSE
To avoid fire hazard, use only a fuse of the correct type, voltage rating, and current rating as specified in the parts
list for this product. Also, ensure that the line selector switch is in the proper position for- the power source being
used.
BATTERY REPLACEMENT
Refer lithium battery replacement to qualified service personnel.
DO NOT OPERATE IN EXPLOSIVE ATMOSPHERES
To avoid explosion. do riot operate this product in an explosive atmosphere unless it has been specifically
certified for such operation.
xxii
Summary of Contents for 318
