TM 11-6625-3145-14
Verification and Adjustment Procedures-318/338 Service
8.
Set serial data generator SETUP as follows;
CODE=ASCII, BAUD=2400, DUPLEX=FULL, SETUP=ASYNC, BITS/CHAR=8, PARITY= NONE, STOPBITS = 1,
TIMING= NORMAL..
9.
Load the following program into the serial data generator:
STEP
MNEMONIC
CODE
1
SEND
#1
2
JMP
#1
10. Load the following hexadecimal data in the serial data generator buffer # 1: E0, E0, E2, E4, E6, E8
11. Press the START key on the serial data generator.
12. Select the DATA DISPLAY STATE TABLE and press the START key.
13. When the 318 displays data on the crt, press the serial data generator STOP key.
14. Check that the 318 display matches the WORD SEQUENCE column on Table 5-12.
15. Set the 318 baud rate to 19.2K (DATA screen).
16. Set the serial data generator baud rate to 19.2K.
17. Set the 318 and the serial data generator controls as indicated in step 1 of Table 5-12 and repeat preceding steps of
Test 6 (11) through (14).
18. Finish steps 2 through 7 Table 5-12 as set up in step (17) of Test 6.
TABLE 5-12.
318 SERIAL STATE ANALYZER TEST STEPS
Serial Data
Step
318
Generator
Word Sequence
1
BITS/WORD = 8
BITS/CHAR = 8
E0, E0, E2, E4, E6. E8
2
BITS/WORD = 7
BITS/CHAR = 7
60, 60, 62, 64, 66, 68
3
BITS/WORD = 6
BITS/CHAR = 6
20, 20, 22, 24, 26, 28
4
BITS/WORD = 5
BITS/CHAR = 5
00, 00, 02, 04, 06, 08
5
BAUD RATE = EXT16
BITS/WORD = 6
BITS/CHAR = 6
20, 20, 22, 24, 26, 28
6
COMM. MODE = SYNC
BITS/WORD = 8
SYNC WORD 1 = 16
SYNC WORD 2 = 16
SETUP = SYNC
BITS/CHAR = 8
CLOCK = DERIVED
(INSERT DATA 16, 16 TO
TOP OF BUFFER #1)
E0, E0, E2, E4, E6, E8,
FF, FF, FF
7
BITS/WORD = 5
SYNC WORD 1 = AD
SYNC WORD 2 = 05
HUNT WORD = 08
BITS/CHAR = 5
00, 02,04,06, 08
5-62
Summary of Contents for 318
