manualshive.com logo in svg

Renesas V850 Series, User Manual, Page: 227 / 1556

Share
Download
Renesas V850 Series User Manual Download Page 227

R01UH0336EJ0102 Rev.1.02

Page 227 of 1538

Jul 17, 2014

V850E2/PG4-L

Section 5 DMA Module

5.5.19

DTSn (n = 0 to 7): DMA Transfer Status Register

This 8-bit register is for checking the state of DMA transfer control.

Access

This register is readable and writable in 1- and 8-bit units.

Address

DTS7: FFFF 748A

H

, DTS6: FFFF 745A

H

, DTS5: FFFF 742A

H

, 

DTS4: FFFF 73FA

H

, DTS3: FFFF 73CA

H

, DTS2: FFFF 739A

H

,

DTS1: FFFF 736A

H

, DTS0: FFFF 733A

H

Initial value

00

H

This register is initialized by a reset from any source.

7

6

5

4

3

2

1

0

DTSnTC

DTSnDT

0

0

DTSnER

DTSnDR

DTSnSR

DTSnDTE

R/W

R/W

R

R

R

R

R/W

R/W

Bit Position

Bit Name

Function

7

DTSnTC

DMA transfer end status
This bit indicates that DMA transfer has been completed. To clear this bit, write 
0 to it after reading it as 1. We recommend using bit-manipulation instructions 
such as CLR1 when writing to this bit.

0: DMA transfer not completed
1: DMA transfer completed

6

DTSnDT

DMA transfer status
This bit indicates that a DMA transfer request has been acknowledged and that
DMA transfer is in progress. It is not set (to 1) when a DMA transfer request is 
simply issued. This bit is cleared (to 0) on completion of DMA transfer. If the 
DTSnDTE bit is 0, this bit can be cleared by the user (and writing to this bit can 
proceed at the same time as writing to the DTSnDTE bit).

0: DMA transfer request acknowledged
1: DMA transfer in progress

3

DTSnER

DMA transfer error flag
This bit indicates that a DMA transfer error has occurred in channel n. It is 
cleared (to 0) when the DTRC0ERR bit of the DTRC0 register is cleared. Note 
that this bit is read-only.

0: No DMA transfer error
1: DMA transfer error

2

DTSnDR

Hardware DMA transfer request flag
This bit indicates the presence or absence of a hardware DMA transfer request 
for channel n. The bit is cleared (to 0) when the hardware DMA transfer request 
is negated. The state of the DTSnDTE bit does not affect the operation of this 
bit. It is not set (to 1) by a software DMA transfer request, or by a hardware 
DMA transfer request when a software DMA transfer request is currently 
selected in the DMA transfer request selection register. Note that this bit is read-
only.

0: No hardware DMA transfer request
1: Hardware DMA transfer request

1

DTSnSR

Software DMA transfer request
This bit selects a software DMA transfer request. If the software DMA transfer 
request is currently selected in the DMA transfer request select register, writing 
1 to this bit and to the DTSnDTE bit starts DMA transfer. This bit is automatically 
cleared (to 0) when DMA transfer has been completed. Writing 0 to this bit 
suspends DMA transfer.

0: No software DMA transfer request
1: Software DMA transfer request

Summary of Contents for V850 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments