manualshive.com logo in svg

Renesas V850 Series, User Manual, Page: 1327 / 1556

Share
Download
Renesas V850 Series User Manual Download Page 1327

R01UH0336EJ0102 Rev.1.02

Page 1327 of 1538

Jul 17, 2014

V850E2/PG4-L

Section 23 A/D Converter

(4)

ADCAnSTC2 – A/D Converter Status Flag Clear Register 2

This register is used to clear the overwrite and result check status flags of 
ADCAnLCR and ADCAnDBiCR.

Access

This register can be written in 8-bit units.
It is always read as 00

H

.

Address

<ADCAn_base1> + 38

H

Initial value

00

H

This register is initialized by any reset.

7

6

5

4

3

2

1

0

ADCAn

LERC1

ADCAn

LERC0

ADCAn

DB2ERC1

ADCAn

DB2ERC0

ADCAn

DB1ERC1

ADCAn

DB1ERC0

ADCAn

DB0ERC1

ADCAn

DB0ERC0

W

W

W

W

W

W

W

W

Table 23-20

ADCAnSTC2 Register Contents

Bit Position

Bit Name

Function

7

ADCAn
LERC1

Clears the overwrite flag (ADCAnLCR.ADCAnLER1 bit):

0: No effect (writing 0 to this bit does not affect the flag).
1: Clears ADCAnLCR.ADCAnLER1

6

ADCAn
LERC0

Clears the result check error flag (ADCAnLCR.ADCAnLER0 bit):

0: No effect (writing 0 to this bit does not affect the flag).
1: Clears ADCAnLCR.ADCAnLER0

5, 3, 1

ADCAn
DBiERC1

Clears the overwrite flag (ADCAnDBiCR.ADCAnDBiER1 bit):

0: No effect (writing 0 to this bit does not affect the flag).
1: Clears ADCAnDBiCR.ADCAnDBiER1

4, 2, 0

ADCAn
DBiERC0

Clears the result check error flag (ADCAnDBiCR.ADCAnDBiER0 bit):

0: No effect (writing 0 to this bit does not affect the flag).
1: Clears ADCAnDBiCR.ADCAnDBiER0

Summary of Contents for V850 Series





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments