manualshive.com logo in svg

Renesas SH7124 R5F7124, Hardware Manual

The Renesas SH7124 R5F7124 is a powerful microcontroller with versatile features. Enhance your understanding of this product by downloading the comprehensive Hardware Manual for free from our website. Explore its capabilities and unleash its full potential with the help of this essential manual.

Share
Download
background image

Section 17   Flash Memory 

 

 

Rev. 3.00  Sep. 27, 2007  Page 621 of 758 

 

 REJ09B0243-0300 

17.7 Usage 

Notes 

17.7.1 Interrupts 

during 

Programming/Erasing 

(1) Download of On-Chip Program 

(1.1) VBR setting change 

Before downloading the on-chip program, VBR must be set to H'84000000. If VBR is set to a 
value other than H'84000000, the interrupt vector table is placed in the user MAT on setting 
H'84000000 to VBR.  

When VBR setting change conflicts with interrupt occurrence, whether the vector table before 
or after VBR is changed is referenced may cause an error. 

Therefore, for cases where VBR setting change may conflict with interrupt occurrence, prepare 
a vector table to be referenced when VBR is H'00000000 (initial value) at the start of the user 
MAT. 

(1.2) SCO download request and interrupt request 

Download of the on-chip programming/erasing program that is initiated by setting the SCO bit 
in FCCS to 1 generates a particular interrupt processing accompanied by MAT switchover. 
Operation when the SCO download request and interrupt request conflicts is described below. 

1.  Contention between SCO download request and interrupt request 

Figure 17.14 shows the timing of contention between execution of the instruction that sets 
the SCO bit in FCCS to 1 and interrupt acceptance. 

 

n

n+1

n+2

n+3

n+4

Fetch

Decoding

Execution

Execution

Execution

(a)

(b)

CPU cycle
CPU operation for instruction
that sets SCO bit to 1

(a)  When the interrupt is accepted at the (n + 1) cycle or before

After the interrupt processing completes, the SCO bit is set to 1 and download is executed.

(b)  When the interrupt is accepted at the (n + 2) cycle or later

The interrupt will conflicts with the SCO download request.  Ensure that no interrupt is generated.

Interrupt acceptance

 

Figure 17.14   Timing of Contention between SCO Download Request and Interrupt Request 

2.  Generation of interrupt requests during downloading  

Ensure that interrupts are not generated during downloading that is initiated by the SCO 
bit. 

 

Summary of Contents for SH7124 R5F7124















































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7124 R5F7124

Patton electronics 1090 Service Manual preview
1090
Brand: Patton electronics Pages: 8
SMART MOD IIC Installation And Service Manual preview
MOD IIC
Brand: SMART Pages: 15
MiLAN E-MCC-1600 Install Manual preview
E-MCC-1600
Brand: MiLAN Pages: 1
Symantec PacketShaper PS-S200 Quick Start Manual preview
PacketShaper PS-S200
Brand: Symantec Pages: 2
Garland INT40G2SR44 User Manual preview
INT40G2SR44
Brand: Garland Pages: 43
Moxa Technologies TAP-125 Series User Manual preview
TAP-125 Series
Brand: Moxa Technologies Pages: 51
ekwb EK-FC285 GTX Classified Installation And Mounting Manual preview
EK-FC285 GTX Classified
Brand: ekwb Pages: 2
C-Smartlink DMH25 Manual preview
DMH25
Brand: C-Smartlink Pages: 7
ZALMAN ZM-2HC2 User Manual preview
ZM-2HC2
Brand: ZALMAN Pages: 8
Alcatel-Lucent 1353 Brochure preview
1353
Brand: Alcatel-Lucent Pages: 12
Renesas M32173T-PTC User Manual preview
M32173T-PTC
Brand: Renesas Pages: 7
Hanwha Techwin WISENET XRN-1610 User Manual preview
WISENET XRN-1610
Brand: Hanwha Techwin Pages: 88
Rimage CDPR3 User Manual preview
CDPR3
Brand: Rimage Pages: 30
Apposite Technologies Linktropy MINI-G User Manual preview
Linktropy MINI-G
Brand: Apposite Technologies Pages: 57
Corsair H100i Manual preview
H100i
Brand: Corsair Pages: 134
ADLINK Technology ROScube-I Series User Manual preview
ROScube-I Series
Brand: ADLINK Technology Pages: 95
Omnia 6FM Installation And Operation Manual preview
6FM
Brand: Omnia Pages: 130
VIPA System 200V PC 288 Manual preview
System 200V PC 288
Brand: VIPA Pages: 54

Brands by name

Popular brands

Load more brands