manualshive.com logo in svg

Renesas SH7124 R5F7124, Hardware Manual

The Renesas SH7124 R5F7124 is a powerful microcontroller with versatile features. Enhance your understanding of this product by downloading the comprehensive Hardware Manual for free from our website. Explore its capabilities and unleash its full potential with the help of this essential manual.

Share
Download
background image

Section 17   Flash Memory 

Rev. 3.00  Sep. 27, 2007  Page 622 of 758 

REJ09B0243-0300 

 

(2) Interrupts during programming/erasing 

Though an interrupt processing can be executed at realtime during programming/erasing of the 
downloaded on-chip program, the following limitations and notes are applied. 

1.  When flash memory is being programmed or erased, the user MAT cannot be accessed. 

Prepare the interrupt vector table and interrupt processing routine in on-chip RAM. Make 
sure the flash memory being programmed or erased is not accessed by the interrupt 
processing routine. If flash memory is read, the read values are not guaranteed. If the 
relevant bank in flash memory that is being programmed or erased is accessed, the error 
protection state is entered, and programming or erasing is aborted. If a bank other than the 
relevant bank is accessed, the error protection state is not entered but the read values are 
not guaranteed. 

2.  Do not rewrite the program data specified by the FMPDR parameter. If new program data 

is to provided by the interrupt processing, temporarily save the new program data in 
another area. After confirming the completion of programming, save the new program data 
in the area specified by FMPDR or change the setting in FMPDR to indicated the other 
area in which the new program data was temporarily saved. 

3.  Make sure the interrupt processing routine does not rewrite the contents of the flash-

memory related registers or data in the downloaded on-chip program area. During the 
interrupt processing, do not simultaneously perform download of the on-chip program by 
an SCO request or programming/erasing. 

4.  At the beginning of the interrupt processing routine, save the CPU register contents. Before 

returning from the interrupt processing, write the saved contents in the CPU registers again. 

5.  When a transition is made to sleep mode or software standby mode in the interrupt 

processing routine, the error protection state is entered and programming/erasing is 
aborted.  
If a transition is made to the reset state, the reset signal should only be released after 
providing a reset input over a period longer than the normal 100 

µ

s to reduce the damage to 

flash memory. 

 

Summary of Contents for SH7124 R5F7124















































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7124 R5F7124

Allnet ALL1682504 Quick Installation preview
ALL1682504
Brand: Allnet Pages: 12
Telebyte 458-LM-E2-36 Quick Start Manual preview
458-LM-E2-36
Brand: Telebyte Pages: 19
Softing CAN-PRO1-PCIE Hardware User Manual preview
CAN-PRO1-PCIE
Brand: Softing Pages: 4
Z3 Technology Z3-SBE264-10 User Instructions preview
Z3-SBE264-10
Brand: Z3 Technology Pages: 67
CNC4PC C52- ESS User Manual preview
C52- ESS
Brand: CNC4PC Pages: 11
mikroElektronika Pressure click Quick Start Manual preview
Pressure click
Brand: mikroElektronika Pages: 2
Zigen IP-Logic ZIG-IPPRO-RX Quick Start Manual preview
IP-Logic ZIG-IPPRO-RX
Brand: Zigen Pages: 4
JETWAY I848ASR1A User Manual preview
I848ASR1A
Brand: JETWAY Pages: 47
JETWAY LI22 Series User Manual preview
LI22 Series
Brand: JETWAY Pages: 63
Intellinet 560665 User Manual preview
560665
Brand: Intellinet Pages: 32
Intel SL6NQ - Xeon 2.4 GHz/533MHz/512 KB CPU Processor 2.4GHz Specification preview
SL6NQ - Xeon 2.4 GHz/533MHz/512 KB CPU Processor 2.4GHz
Brand: Intel Pages: 56
Adaptec 2025ZCR - SCSI RAID Storage Controller Datasheet preview
2025ZCR - SCSI RAID Storage Controller
Brand: Adaptec Pages: 2
Rohm BD7682FJ-EVK-301 Quick Start Manual preview
BD7682FJ-EVK-301
Brand: Rohm Pages: 6
VAMISOUND Schoeps electret Building Instructions preview
Schoeps electret
Brand: VAMISOUND Pages: 15
3Com X5 Quick Start preview
X5
Brand: 3Com Pages: 2
3Com 3CRWE825075A Quick Start Manual preview
3CRWE825075A
Brand: 3Com Pages: 8
3Com AirProtect Enterprise Engine 6100 Quick Setup Manual preview
AirProtect Enterprise Engine 6100
Brand: 3Com Pages: 12
2Wire i3812V User Manual preview
i3812V
Brand: 2Wire Pages: 20

Brands by name

Popular brands

Load more brands