manualshive.com logo in svg

Renesas SH7124 R5F7124, Hardware Manual

The Renesas SH7124 R5F7124 is a powerful microcontroller with versatile features. Enhance your understanding of this product by downloading the comprehensive Hardware Manual for free from our website. Explore its capabilities and unleash its full potential with the help of this essential manual.

Share
Download
background image

Section 12   Serial Communication Interface (SCI) 

 

 

Rev. 3.00  Sep. 27, 2007  Page 431 of 758 

 

 REJ09B0243-0300 

12.3.10  Bit Rate Register (SCBRR) 

SCBRR is an 8-bit register that, together with the baud rate generator clock source selected by the 
CKS1 and CKS0 bits in the serial mode register (SCSMR), determines the serial transmit/receive 
bit rate. 

The CPU can always read and write to SCBRR. 

The SCBRR setting is calculated as follows: 

Bit:

Initial value:

R/W:

7

6

5

4

3

2

1

0

1

1

1

1

1

1

1

1

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

 

 

• 

Asynchronous mode: 

 

N =

 

×

  10

6

  - 1

64 

×

 2

2n-1

 

×

 B

P

φ

 

 

• 

Clock synchronous mode: 

 

N =

× 

 10

6

  - 1

8 

× 

 2

2n-1

 

× 

B

P

φ

 

 

B:  Bit rate (bits/s) 
N:  SCBRR setting for baud rate generator (0 

≤

 N 

≤

 255) 

 

(The setting value should satisfy the electrical characteristics.) 

P

φ

:  Operating frequency for peripheral modules (MHz) 

n: 

Baud rate generator clock source (n 

=

 0, 1, 2, 3) (for the clock sources and values of  

 

n, see table 12.3.) 

Summary of Contents for SH7124 R5F7124















































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7124 R5F7124

dbx Zone Pro 640 Manual preview
Zone Pro 640
Brand: dbx Pages: 2
dbx 166 Quick Start Manual preview
166
Brand: dbx Pages: 17
Phytec L-843e.A1 Hardware Manual preview
L-843e.A1
Brand: Phytec Pages: 53
ZyXEL Communications EOC350 Series Quick Start Manual preview
EOC350 Series
Brand: ZyXEL Communications Pages: 2
Dahua NVS0X04DH Quick Start Manual preview
NVS0X04DH
Brand: Dahua Pages: 24
Acces I/O products MPCIE-ICM232-2 Hardware Manual preview
MPCIE-ICM232-2
Brand: Acces I/O products Pages: 5
Enertronica Santerno SINUS H PROFInet User Manual preview
SINUS H PROFInet
Brand: Enertronica Santerno Pages: 34
Keithley PDISO-8 User Manual preview
PDISO-8
Brand: Keithley Pages: 71
Thermalright AXP-100H MUSCLE Manual preview
AXP-100H MUSCLE
Brand: Thermalright Pages: 36
ICP DAS USA PISO-725 Series Quick Start Manual preview
PISO-725 Series
Brand: ICP DAS USA Pages: 8
Patton electronics Model 2711 User Manual preview
Model 2711
Brand: Patton electronics Pages: 13
Altera Cyclone IV GX Reference Manual preview
Cyclone IV GX
Brand: Altera Pages: 40
Milesight Pro UR32 Quick Start Manual preview
Pro UR32
Brand: Milesight Pages: 15
Navitar 1-62643 Dimensional Drawing preview
1-62643
Brand: Navitar Pages: 1
Ebyte ECAN-W01 User Manual preview
ECAN-W01
Brand: Ebyte Pages: 23
BiPOM Electronics CG9103-2RS232-1USB User Manual preview
CG9103-2RS232-1USB
Brand: BiPOM Electronics Pages: 8
Analog Devices EZ-KIT LITE ADSP-2191 Manual preview
EZ-KIT LITE ADSP-2191
Brand: Analog Devices Pages: 98
Foxconn RAID Foldout Introduction preview
RAID Foldout
Brand: Foxconn Pages: 1

Brands by name

Popular brands

Load more brands