manualshive.com logo in svg

Renesas SH7124 R5F7124, Hardware Manual

The Renesas SH7124 R5F7124 is a powerful microcontroller with versatile features. Enhance your understanding of this product by downloading the comprehensive Hardware Manual for free from our website. Explore its capabilities and unleash its full potential with the help of this essential manual.

Share
Download
background image

Section 5   Exception Handling 

Rev. 3.00  Sep. 27, 2007  Page 72 of 758 

REJ09B0243-0300 

 

5.1.2 

Exception Handling Operations 

The exceptions are detected and the exception handling starts according to the timing shown in 
table 5.2. 

Table 5.2 

Timing for Exception Detection and Start of Exception Handling 

Exception 

 

Timing of Source Detection and Start of Exception Handling 

Reset 

Power-on reset  Started when the 

RES

 pin changes from low to high or when the 

WDT overflows. 

 

Manual reset 

Started when the

 

MRES

 pin changes from low to high or when the 

WDT overflows. 

Address error 

Interrupt  

Detected during the instruction decode

 

stage and started after the 

execution of the current instruction is completed. 

Instruction 

Trap instruction  Started by the execution of the TRAPA instruction. 

 General 

illegal 

instructions  

Started when an undefined code placed at other than a delay slot 
(immediately after a delayed branch instruction) is decoded. 

 Illegal 

slot 

instructions  

Started when an undefined code placed at a delay slot 
(immediately after a delayed branch instruction) or an instruction 
that changes the PC value is detected. 

 

When exception handling starts, the CPU operates  

Exception Handling Triggered by Reset:

 The initial values of the program counter (PC) and 

stack pointer (SP) are fetched from the exception handling vector table (PC from the address 
H'00000000 and SP

 

from the address H'00000004 when a power-on reset. PC from the address 

H'00000008 and SP from the address H'0000000C when a manual reset.). For details, see section 
5.1.3, Exception Handling Vector Table. H'00000000 is then written to the vector base register 
(VBR), and H'F (B'1111) is written to the interrupt mask bits (I3 to I0) in the status register (SR). 
The program starts from the PC address fetched from the exception handling vector table. 

Exception Handling Triggered by Address Error, Interrupt, and Instruction:

 SR and PC are 

saved to the stack indicated by R15. For interrupt exception handling, the interrupt priority level is 
written to the interrupt mask bits (I3 to I0) in SR. For address error and instruction exception 
handling, bits I3 to I0 are not affected. The start address is then fetched from the exception 
handling vector table and the program starts from that address. 

Summary of Contents for SH7124 R5F7124















































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7124 R5F7124

IEI Technology PCIE-Q470 Quick Installation Manual preview
PCIE-Q470
Brand: IEI Technology Pages: 19
IEI Technology KINO-DH420 User Manual preview
KINO-DH420
Brand: IEI Technology Pages: 87
IEI Technology HPE-4S2 Quick Installation Manual preview
HPE-4S2
Brand: IEI Technology Pages: 3
ebm-papst VBH0630CTTRS Operating Instructions Manual preview
VBH0630CTTRS
Brand: ebm-papst Pages: 16
Alacritech 1000x1 Hardware Installation Manual preview
1000x1
Brand: Alacritech Pages: 20
Usr USR4504 Installation Manual preview
USR4504
Brand: Usr Pages: 2
Cromemco 32K Bytesaver Instruction Manual preview
32K Bytesaver
Brand: Cromemco Pages: 46
Verizon Wireless PC 3220 Owner'S Manual preview
PC 3220
Brand: Verizon Wireless Pages: 39
Ubiquiti PBE-5AC-300-ISO Quick Start Manual preview
PBE-5AC-300-ISO
Brand: Ubiquiti Pages: 28
Advantech MIC-730AI User Manual preview
MIC-730AI
Brand: Advantech Pages: 36
FDI ELI70-CR Quick Start Manual preview
ELI70-CR
Brand: FDI Pages: 2
Aaeon SBC-657B Manual preview
SBC-657B
Brand: Aaeon Pages: 61
ZALMAN RESERATOR1 V2 Installation And Operational Manual preview
RESERATOR1 V2
Brand: ZALMAN Pages: 18
Hama 00176547 Operating Instruction preview
00176547
Brand: Hama Pages: 25
Oracle Acme Packet 3900 Hardware Installation And Maintenance Manual preview
Acme Packet 3900
Brand: Oracle Pages: 70
McIntosh MX160 Owner'S Manual preview
MX160
Brand: McIntosh Pages: 44
FOR-A USF-105PS Operation Manuals preview
USF-105PS
Brand: FOR-A Pages: 37
VIA Technologies LPC-01 Quick Manual preview
LPC-01
Brand: VIA Technologies Pages: 2

Brands by name

Popular brands

Load more brands