HP AE370A - Brocade 4Gb SAN Switch 4/12 Administrator'S Manual Download | Manualshive

Page: 367 / 447

background image

Fabric OS 5.2.x administrator guide 367

21 Configuring and monitoring FCIP tunneling

The Fibre Channel over IP (FCIP) Tunneling Service is an optional feature that enables you to use Fibre

Channel “tunnels” to connect SANs over IP-based networks. An FCIP tunnel transports data between a pair

of Fibre Channel switches. You can have more than one TCP connection between the pair of Fibre Channel

switches. However, from the Fibre Channel fabric point of view, the FCIP tunnel is just a connection

between switches, and all the IP network and protocols remain invisible.

Supported platforms for FCIP

Fabric OS supports FCIP ISLs between two SilkWorm switches (SilkWorm 7500 or SilkWorm 48000 with

an FR4-18i blade).
The GbE ports on the FC4-16IP do not support FCIP tunneling.

NOTE:

The Fabric OS 5.2.0 FCIP Tunneling Service is not compatible with the XPath FCIP service; nor is

it compatible with any other vendor’s implementation

.

About FCIP tunneling

FCIP tunneling enables you to connect fabrics over an IP connection. Depending on the port type you

select, the fabrics can merge or remain separate, while sharing devices. This enables you, for example, to

connect one central office to different branch offices without having to merge the fabrics.
The port types for FCIP tunneling are either VE_Port or VEX_Port. An FCIP tunnel using VE_Ports will merge

the two fabrics, and an FCIP tunnel using a VEX_Port will not merge the fabrics. A VEX_Port can only

connect to a VE_Port.
Fibre Channel frame encapsulation on one port and the reconstruction of Fibre Channel frames on the

other port is transparent to the initiator and target.
Fabric OS supports FCIP ISLs between two supported HP StorageWorks switches (400 MP Router or 4/256

SAN Director with B-Series MP Router blade) or routers.
The tunnel on each GbE port are numbered 0 through 7, and each tunnel corresponds to a virtual GbE

port. For example, tunnel 0 on GbE port 0 corresponds to logical FC port 16; tunnel 1 on GbE port 1

corresponds to logical FC port 25. The GbE physical ports enable you to configure the following tunnels

and corresponding virtual ports:

Table 89

Tunnels and virtual port numbering once configured

Physical ports

Tunnels

(portshow fciptunnel

slot/ge)

Virtual ports

(switchshow

ge0

0 through 7

16 through 23

(area numbers might be different

depending on the slot chosen for

the B-Series MP Router blade)

ge1

0 through 7

24 through 31

(area numbers might be different

depending on the slot chosen for

the B-Series MP Router blade)

«
...
365
366
367
368
369
...
»

Summary of Contents for AE370A - Brocade 4Gb SAN Switch 4/12
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AE370A - Brocade 4Gb SAN Switch 4/12

Brand: Accessory Power Pages: 4

Brand: HAGOR Pages: 8

SeaLINK+232 2101

Brand: SeaLevel Pages: 15

Brand: C2G Pages: 24

Brand: Intermec Pages: 102

Brand: YOKOGAWA Pages: 2

Mini Port Replicator

Brand: Keyspan Pages: 41

Brand: Delta Pages: 4

Brand: 3idee Pages: 7

Brand: Velleman Pages: 18

Brand: IBM Pages: 11

Brand: NETGEAR Pages: 12

Brand: Mr Handsfree Pages: 68

Brand: Cochlear Pages: 46

Xesar Expert EX9132CST

Brand: EVVA Pages: 12

Brand: Chauvet Pages: 3

IDATA HDMI-VGA3

Brand: Techly Pages: 12

SST DeviceNet 5136-DNS-200X

Brand: Woodhead Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands