manualshive.com logo in svg

HP AE370A - Brocade 4Gb SAN Switch 4/12, Administrator'S Manual

The HP AE370A - Brocade 4Gb SAN Switch 4/12 is a powerful networking solution providing superior performance. To access the comprehensive Administrator's Manual, visit our website and download it for free. Unlock the full potential of this product with the detailed manual available at manualshive.com.

Share
Download
background image

Fabric OS 5.2.x administrator guide 201

fabric to another—over the backbone or edge fabric through this virtual domain—without merging the 

two fabrics. Translate phantom domains are sometimes referred to as “translate domains,” or “xlate 

domains.” If a B-Series MP Router blade is attached to an edge fabric using an EX_Port, it will create 

translate phantom domains in the fabric corresponding to the imported edge fabrics with active LSANs 

defined. If you import devices into the backbone fabric, then a translate phantom domain is created in 

the backbone device (in addition to the one in the edge fabric). 
If you lose connectivity to the edge fabric due to link failures or the IFL being disabled (for example, by 

issuing the 

portDisable

 command from the switch in the attached fabric) translate phantom domains 

remain visible. This prevents unnecessary fabric disruptions caused by translate phantom domains 

repeatedly going offline and online due to corresponding IFL failures. To remove the translate phantom 

domain in the backbone, disable all EX_Ports or VEX_Ports through which the translate phantom 

domain was created. 

Figure 8

 shows a metaSAN with a backbone consisting of one 400 MP Router connecting hosts in 

Edge Fabric 1 and 3 with storage in Edge Fabric 2 and the backbone through the use of LSANs. A 

device is shared between:
• The backbone and Edge Fabric 1
• Edge Fabric 1 and Edge Fabric 2
• Edge Fabric 2 and Edge Fabric 3

Figure 9

 shows a metaSAN consisting of three edge fabrics connected through a 4/256 SAN Director 

containing an B-Series MP Router blade with interfabric links.

Figure 9

A metaSAN with interfabric links

Edge

fabric 2

Host

Target

Target

Edge

fabric 1

Edge

fabric 3

Fibre

Channel

switch

Fibre

Channel

switch

E_Port

E_Port

E_Port

EX_Ports

IFL

IFL

Long Distance IFL

4/256 SAN Director with
B-Series MP Router blade

25313a

Summary of Contents for AE370A - Brocade 4Gb SAN Switch 4/12
































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AE370A - Brocade 4Gb SAN Switch 4/12

Tamio U1 Quick Installation Manual preview
U1
Brand: Tamio Pages: 2
3idee smsng-s32bm Assembly Instructions preview
smsng-s32bm
Brand: 3idee Pages: 5
3idee smsng-cv27 Assembly Instructions preview
smsng-cv27
Brand: 3idee Pages: 5
3idee hp-pro-g6 Assembly Instructions Manual preview
hp-pro-g6
Brand: 3idee Pages: 7
HighPoint RocketRAID 3220 User Manual preview
RocketRAID 3220
Brand: HighPoint Pages: 80
ZyXEL Communications Prestige 2002 Series Quick Start Manual preview
Prestige 2002 Series
Brand: ZyXEL Communications Pages: 20
BIG ASS FANS BACnet Adapter Installation Manual preview
BACnet Adapter
Brand: BIG ASS FANS Pages: 56
NETGEAR Powerline Adaptor Kit Connecting Manual preview
Powerline Adaptor Kit
Brand: NETGEAR Pages: 8
WMS 100 Image Quick Reference preview
100 Image
Brand: WMS Pages: 16
StarTech.com PCI220USB Instruction Manual preview
PCI220USB
Brand: StarTech.com Pages: 10
Oracle Dual Port 25 Gb User Manual preview
Dual Port 25 Gb
Brand: Oracle Pages: 88
3idee hp-z Assembly Instructions Manual preview
hp-z
Brand: 3idee Pages: 7
NETGEAR GA511 - Gigabit Ethernet PC Card User Manual preview
GA511 - Gigabit Ethernet PC Card
Brand: NETGEAR Pages: 50
ZyXEL Communications omni.net LCD series Quick Start Manual preview
omni.net LCD series
Brand: ZyXEL Communications Pages: 53
ZyXEL Communications FN-300 Series User Manual preview
FN-300 Series
Brand: ZyXEL Communications Pages: 3
Radio Shack 1201526 User Manual preview
1201526
Brand: Radio Shack Pages: 10
Radicom RW8300-MB2-H Designer'S Manual preview
RW8300-MB2-H
Brand: Radicom Pages: 62
Eminent EM4577 User Manual preview
EM4577
Brand: Eminent Pages: 8

Brands by name

Popular brands

Load more brands