HP AE370A - Brocade 4Gb SAN Switch 4/12 Administrator'S Manual Download

Page: 348 / 447

348 Administering Advanced Zoning

name server returns only those devices that are in the same zone as the initiator. Devices that are not

part of the zone are not returned as accessible devices.

Table 82

shows the various switch models, the hardware Zoning methodology for each, and tips for best

usage.

Table 82

Enforcing hardware Zoning

Fabric Type

Methodology

Best practice

HP StorageWorks

1 GB

Enables hardware-enforced Zoning

only on domain, port zones; WWN or

mixed zones are not

hardware-enforced. Any domain, port

zone that overlaps a mixed or WWN

zone is not hardware-enforced.
An overlap occurs when a member

specified by WWN is connected to a

port in a domain, port zone. The

domain, port zone loses its hardware

enforcement even though a review of

the zone configuration does not

indicate it.

Use

domain, port

identifiers. Do

not identify a zone member by its

WWN.

HP StorageWorks

2/8 EL, HP

StorageWorks

MSA SAN Switch

2/8, HP

StorageWorks

2/16 EL,

HP StorageWorks

2/16, 4/16 SAN

Switch and 4/8

SAN Switch,

SAN Switch

4/32, 4/64 SAN

Switch, 400 MP

Router, SAN

Director 2/128,

and 4/256 SAN

Director models

Enable hardware-enforced Zoning on

domain, port zones, and WWN

zones. Overlap of similar zone types

does not result in the loss of hardware

enforcement. Overlap with other zone

type results in the loss of hardware

enforcement.
As in the HP StorageWorks 1 GB

switches, connecting a device

specified by WWN into a port

specified in a domain, port zone

results in loss of the hardware

enforcement in both zones.

Use either WWN or

domain, port

identifiers.

Mixed switches

Enable hardware-enforced Zoning

according to each switch type. Use the

portZoneShow

command to find the

zone type to which a device is

attached.

Use

domain, port

identifiers.

You can use WWN identifiers if

you place disk and tape targets

on 3000-series, and SAN Director

2/128 models, and do not use

domain, port

identifiers.

Summary of Contents for AE370A - Brocade 4Gb SAN Switch 4/12
































































































































































































































































































































































































































































Search results

Summary of Contents for AE370A - Brocade 4Gb SAN Switch 4/12

Reviews:

Related manuals for AE370A - Brocade 4Gb SAN Switch 4/12

Brands by name

Popular brands

HP AE370A - Brocade 4Gb SAN Switch 4/12, Administrator'S Manual

Search results

Summary of Contents for AE370A - Brocade 4Gb SAN Switch 4/12

Reviews:

Related manuals for AE370A - Brocade 4Gb SAN Switch 4/12

Brands by name

Popular brands