Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 254 | Manualshive

Page: 254 / 440

background image

CAUTION!

•

Never drive with your foot resting on the clutch
pedal, or try to hold the vehicle on a hill with the
clutch pedal partially engaged, as this will cause
abnormal wear on the clutch. Refer to “Electronic
Brake Control System/Hill Start Assist

ⴖ

in this

section.

•

Failure to press the clutch pedal fully to the floor
may cause increased shift efforts, and may result
in damage to the clutch and transmission.

•

Do not rest your hand on the shift lever while
driving, as this may result in transmission syn-
chronizer damage.

NOTE:

During cold weather, you may experience in-

creased effort in shifting until the transmission fluid
warms up. This is normal.

Shifting

Fully press the clutch pedal before shifting gears. As you
release the clutch pedal, lightly press the accelerator
pedal.

Manual Shifter

252

STARTING AND OPERATING

«
...
252
253
254
255
256
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: ABL Pages: 176

Brand: ABL Pages: 94

Multiple G9F18 AU000

Brand: Genesis Pages: 3

Brand: Camcar Pages: 6

Brand: ABL Pages: 4

Brand: AddSecure Pages: 14

Brand: Ecco Pages: 12

Brand: Fiat Pages: 24

Brand: Valeo Pages: 28

Brand: M7 SPEED Pages: 6

Brand: Metra Electronics Pages: 8

Brand: Rugged Ridge Pages: 5

Brand: Volvo Pages: 92

Brand: Jaeger Pages: 14

Brand: Reliant Pages: 206

Brand: Ranger design Pages: 22

Indash 75114-296

Brand: Panavise Pages: 2

V2 Two-Bike Carrier

Brand: LetsGoAero Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands