Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 18 | Manualshive

Page: 18 / 440

background image

All of the RKE transmitters provided with your new
vehicle have been programmed to the vehicle electronics.

Replacement Keys

NOTE:

Only RKE transmitters that are programmed to

the vehicle electronics can be used to start and operate
the vehicle. Once a transmitter is programmed to a
vehicle, it cannot be programmed to any other vehicle.

CAUTION!

Always remove the keys from the vehicle and lock all
doors when leaving the vehicle unattended.

At the time of purchase, the original owner is provided
with a four-digit Personal Identification Number (PIN).
Keep the PIN in a secure location. This number is
required for authorized dealer replacement of RKE trans-
mitters. Duplication of RKE transmitters may be per-
formed at an authorized dealer or by using the Customer

Key Programming procedure. This procedure consists of
programming a blank transmitter to the vehicle electron-
ics. A blank transmitter is one that has never been
programmed.

NOTE:

When having the Sentry Key

威

Immobilizer

System serviced, bring all vehicle RKE transmitters with
you to the authorized dealer.

Customer Key Programming

If you have two valid RKE transmitters with integrated
keys, you can program new transmitters to the system by
performing the following steps:

1. Insert the first valid integrated key into the ignition
switch and turn the ignition switch to the ON position for
at least three seconds, but no longer than 15 seconds.
Turn the ignition switch to the LOCK position and
remove the first key.

16

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
16
17
18
19
20
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

PRIME DESIGN VRI3-E-PM11

Brand: Safe Fleet Pages: 12

Brand: Kuda-Phonebase Pages: 3

Brand: Trailboss Pages: 5

v.LOGiC Intelligent Solution V5-NTG46

Brand: Caraudio-Systems Pages: 18

ADARAC Aluminum M Series

Brand: aci Pages: 16

Brand: Imiola HAK-POL Pages: 3

Brand: Opel Pages: 32

Brand: DriveRight Pages: 16

Brand: r.LiNK Pages: 21

Brand: Toyota Pages: 672

Brand: Toyota Pages: 204

QuadraTop Adventure Top S

Brand: Quadratec Pages: 13

Brand: Rosco Pages: 12

Brand: TIS Pages: 6

Brand: Ford Pages: 312

Brand: X-Armour Pages: 16

Brand: Truma Pages: 84

Brand: Federal Signal Corporation Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands