Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 55 | Manualshive

Page: 55 / 440

background image

Enhanced Accident Response System

In the event of an impact that causes airbag deployment,
with the vehicle stopped, the vehicle communication
network intact, and the power intact, the Enhanced
Accident Response System performs the following func-
tions:

•

Cuts off fuel to the engine.

•

Flashes hazard lights.

•

Turns on the interior lights, which remain on as long as
the battery has power or until the ignition key is
removed.

•

Unlocks the doors automatically.

NOTE:

The interior lights can only be deactivated if the

key is removed from the ignition switch or the vehicle is
driven.

Maintaining Your Airbag System

WARNING!

•

Modifications to any part of the airbag system
could cause it to fail when you need it. You could
be injured because the airbags are not there to
protect you. Do not modify the components or
wiring, including adding any kind of badges or
stickers to the steering wheel hub trim cover or the
upper passenger side of the instrument panel. Do
not modify the front bumper, vehicle body struc-
ture, or frame.

•

You need proper knee impact protection in a
collision. Do not mount or locate any aftermarket
equipment on or behind the knee impact bolster.

•

It is dangerous to try to repair any part of the
airbag system yourself. Be sure to tell anyone who
works on your vehicle that it has airbags.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

53

2

«
...
53
54
55
56
57
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Daihatsu Pages: 1718

Brand: Yakima Pages: 8

Brand: Gator Pages: 8

Brand: tams elektronik Pages: 44

Brand: Great Wall Pages: 18

Brand: WIX Pages: 2

Brand: Yutrax Pages: 8

Brand: Volvo Pages: 211

Brand: Scion Pages: 24

2013 GMC Savana

Brand: GMC Pages: 398

PRIME DESIGN HRR-369-E-UM3-96

Brand: Safe Fleet Pages: 12

Brand: Kocchi's Pages: 4

Brand: travall Pages: 4

LED Dominator TAM83S2

Brand: Whelen Engineering Company Pages: 2

Brand: AutoLoc Pages: 6

Brand: Westfalia Pages: 10

Brand: PUTCO Pages: 3

Escalade 2004 Escalade ESV

Brand: Cadillac Pages: 472

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands