Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 31 | Manualshive

Page: 31 / 440

background image

Power Door Locks

The power door lock switch is located on each door trim
panel. Use this switch to lock or unlock the doors.

If you press the power door lock switch while the key is
in the ignition, and either door is open, the power locks
will not operate. This prevents you from accidentally

locking the key in the vehicle. Removing the key or
closing the door will allow the locks to operate. If a door
is open, the key is in the ignition, and the ignition is in the
LOCK or ACC position, a chime will sound as a reminder
to remove the key.

Automatic Door Locks

The doors will lock automatically if all of the following
conditions are met:

1. The Automatic Door Locks feature is enabled

2. The transmission is in gear

3. All doors are closed

4. The throttle is pressed

5. The vehicle speed is above 15 mph (24 km/h), and

6. The doors were not previously locked using the power
door lock switch or Remote Keyless Entry (RKE)
transmitter.

Power Door Lock Switch

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

29

2

«
...
29
30
31
32
33
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

10-8002-C11998B

Brand: Saleen Pages: 12

2013 Buick Verano

Brand: Buick Pages: 5

MOLLE PANELS RAM 2500

Brand: PUTCO Pages: 4

Brand: Westfalia Pages: 18

Brand: Quadratec Pages: 8

Brand: Veldo Teknoloji Pages: 32

FXX ATM Emulator

Brand: BMW Pages: 5

Brand: Whispbar Pages: 15

Truck 2500 2018

Brand: RAM Pages: 32

BreadCrumb DX2 Series

Brand: Rajant Pages: 11

Brand: Telwin Pages: 32

Cutlass 1978 Series

Brand: Oldsmobile Pages: 97

Brand: Emerson Pages: 24

Brand: Emerson Pages: 32

Brand: Steinhof Pages: 2

Brand: FORM FIT Pages: 4

Brand: Honda Pages: 24

PRO-YD-DR02 Series

Brand: Spyder Auto Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands