Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 185 | Manualshive

Page: 185 / 440

background image

to seek up and the left switch to seek down. The radio
will remain tuned to the new station until you make
another selection. Holding either button will bypass
stations without stopping until you release it.

SCAN Button

Pressing the SCAN button causes the tuner to search for
the next listenable station in AM, FM or Satellite (if
equipped) frequencies, pausing for five seconds at each
listenable station before continuing to the next. To stop
the search, press the SCAN button a second time.

Voice Recognition Button uconnect

威

phone — If

Equipped

Press this button to operate the uconnect

威

phone feature

(if equipped). Refer to “uconnect

威

phone” in Section 3.

If your vehicle is not equipped with or this feature is not
available on your vehicle, a “Not Equipped With
uconnect” message will display on the radio screen.

Phone Button uconnect

威

phone — If Equipped

Press this button to operate the uconnect

威

phone feature

(if equipped). Refer to “uconnect

威

phone” in Section 3.

If your vehicle is not equipped with or this feature is not
available on your vehicle, a “Not Equipped With
uconnect” message will display on the radio screen.

TIME Button

Press the TIME button to alternate locations of the time
and frequency display.

Clock Setting Procedure

1. Press and hold the TIME button until the hours blink.

2. Adjust the hours by turning the right side TUNE/
SCROLL control knob.

3. After adjusting the hours, press the right side TUNE/
SCROLL control knob to set the minutes. The minutes
will begin to blink.

UNDERSTANDING YOUR INSTRUMENT PANEL

183

4

«
...
183
184
185
186
187
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: PAC Pages: 4

Brand: PAC Pages: 4

Brand: PAC Pages: 8

Brand: PAC Pages: 5

Brand: UMBRA RIMORCHI Pages: 18

Brand: PEUGEOT Pages: 128

Brand: Schumacher Electric Pages: 87

2009 ESCALADE ESV

Brand: Cadillac Pages: 602

Brand: AC Schnitzer Pages: 20

Brand: Raytel LLC Pages: 40

Brand: iArmor Pages: 4

Brand: Whispbar Pages: 14

Brand: STARLANE Pages: 24

Brand: E&G Classics Pages: 3

Brand: C-KO Pages: 4

Brand: Toyota Pages: 295

Brand: Yakima Pages: 12

Platinum Pro Plug-in

Brand: Haltech Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands