Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 292 | Manualshive

Page: 292 / 440

background image

Tire Loading and Tire Pressure

Tire Placard Location

NOTE:

The proper cold tire inflation pressure is listed

on the driver’s side B-Pillar.

Tire and Loading Information Placard

This placard tells you important information about
the:
1) number of people that can be carried in the vehicle
2) total weight your vehicle can carry
3) tire size designed for your vehicle
4) cold tire inflation pressures for the front, rear, and
spare tires.

Tire and Loading Information Placard

290

STARTING AND OPERATING

«
...
290
291
292
293
294
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: JETBAG Pages: 44

Brand: Kia Pages: 54

Brand: Metra Electronics Pages: 2

STRONGARM RVR303

Brand: Blue Giant Pages: 48

Brand: Ford Pages: 2

2012 Truck Chassis cab

Brand: RAM Pages: 506

Brand: UAZ Pages: 112

Brand: Air Lift Pages: 28

Brand: Dolphin Pages: 16

Brand: Ranger design Pages: 22

Brand: Volvo Pages: 18

Brand: Suzuki Pages: 504

Brand: Bulldog Security Pages: 7

Brand: Smappee Pages: 28

Brand: Curt Group Pages: 2

Brand: Volkswagen Zubehör Pages: 133

ASENTO EV-COLC15R

Brand: ADAPT SOLUTIONS Pages: 22

Brand: ACV Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands