manualshive.com logo in svg

Dodge 2009 Challenger SRT8, Owner'S Manual

The 2009 Dodge Challenger SRT8 is a powerful and iconic muscle car, built for speed and style. To fully maximize your driving experience, it's crucial to have the corresponding Owner's Manual. Download the manual for free from our website, providing insightful instructions and essential information for your vehicle.

Share
Download
background image

PARKING BRAKE

The parking brake should always be applied when the
driver is not in the vehicle.

The “Brake Warning Light” in the instrument cluster will
turn on when the parking brake is applied and the
ignition switch is ON.

NOTE:

This light only shows that the parking brake is

applied. It does not show the degree of brake application.

When parking on a flat surface, place the shift lever in the
PARK position (automatic transmission), R (Reverse) or
1st gear (manual transmission) first and then apply the
parking brake.

When parking on a hill, it is important to apply the
parking brake before placing the shift lever in PARK,
otherwise the load on the transmission locking mecha-
nism may make it difficult to move the shift lever out of
PARK. As an added precaution, turn the front wheels
toward the curb on a downhill grade and away from the
curb on an uphill grade.

270

STARTING AND OPERATING

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Cadillac 2011 CTS COUPE Personalization Manual preview
2011 CTS COUPE
Brand: Cadillac Pages: 20
Cadillac 2011 CTS COUPE Specifications preview
2011 CTS COUPE
Brand: Cadillac Pages: 2
Cadillac 2009 CTS Owner'S Manual preview
2009 CTS
Brand: Cadillac Pages: 494
Cadillac 2008 Escalade Owner'S Manual preview
2008 Escalade
Brand: Cadillac Pages: 500
Cadillac 2006 Escalade Warranty And Owner Assistance Information preview
2006 Escalade
Brand: Cadillac Pages: 40
Cadillac 2004 DeVille Owner'S Manual preview
2004 DeVille
Brand: Cadillac Pages: 432
Cadillac 1997 Catera Owner'S Manual preview
1997 Catera
Brand: Cadillac Pages: 338
Cadillac 2009 STS Get To Know preview
2009 STS
Brand: Cadillac Pages: 20
Cadillac 2005 STS Owner'S Manual preview
2005 STS
Brand: Cadillac Pages: 438
EAL Formula 523585 Assembly Instructions preview
Formula 523585
Brand: EAL Pages: 4
IAME Parilla X30 Assembly Instructions And User'S Manual preview
Parilla X30
Brand: IAME Pages: 17
Roav R5141 Owner'S Manual preview
R5141
Brand: Roav Pages: 10
Ultra-tow XTP Series Owner'S Manual preview
XTP Series
Brand: Ultra-tow Pages: 14
Mercedes-Benz 300D 2.5 1990 Owner'S Manual preview
300D 2.5 1990
Brand: Mercedes-Benz Pages: 121
Menabo BIKE PRO Fitting Instructions Manual preview
BIKE PRO
Brand: Menabo Pages: 8
Camtree G-51 Instruction Manual preview
G-51
Brand: Camtree Pages: 5
CITROEN C8 NaviDrive Manual preview
C8 NaviDrive
Brand: CITROEN Pages: 52
Yakima RoadShower 10G Quick Start Manual preview
RoadShower 10G
Brand: Yakima Pages: 12

Brands by name

Popular brands

Load more brands