Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 42 | Manualshive

Page: 42 / 440

background image

5. Position the shoulder belt on your chest so that it is
comfortable and not resting on your neck. The retractor
will withdraw any slack in the belt.

6. To release the belt, push the red button on the buckle.
The belt will automatically retract to its stowed position.
If necessary, slide the latch plate down the webbing to
allow the belt to retract fully.

WARNING!

A frayed or torn belt could rip apart in a collision and
leave you with no protection. Inspect the belt system
periodically, checking for cuts, frays, or loose parts.
Damaged parts must be replaced immediately. Do
not disassemble or modify the system. Seat belt
assemblies must be replaced after a collision if they
have been damaged (bent retractor, torn webbing,
etc.).

Removing Slack From Belt

40

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
40
41
42
43
44
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Hama Pages: 2

Brand: Abarth Pages: 36

Brand: Raven Pages: 24

Brand: Weather Guard Pages: 4

Brand: JASTEC Pages: 12

Brand: RAM Pages: 20

CommCenter D1 Series

Brand: Federal Signal Corporation Pages: 16

Multiple G9F18 AU000

Brand: Genesis Pages: 3

Brand: Trailboss Pages: 5

Chevrolet Silverado 2500HD 2021

Brand: GMC Pages: 433

Brand: Kuda Pages: 3

Brand: FALCON RIDGE Pages: 8

Brand: Scosche Pages: 8

Hypercharger HYC 075

Brand: Alpitronic Pages: 64

Brand: P-Invent Pages: 4

2000 Oldsmobile Intrigue

Brand: Oldsmobile Pages: 348

Brand: Thule Pages: 4

XC70 - ANNEXE 808

Brand: Volvo Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands