manualshive.com logo in svg

Dodge 2009 Challenger SRT8, Owner'S Manual

The 2009 Dodge Challenger SRT8 is a powerful and iconic muscle car, built for speed and style. To fully maximize your driving experience, it's crucial to have the corresponding Owner's Manual. Download the manual for free from our website, providing insightful instructions and essential information for your vehicle.

Share
Download
background image

Treadwear

The Treadwear grade is a comparative rating, based on
the wear rate of the tire when tested under controlled
conditions on a specified government test course. For
example, a tire graded 150 would wear one and one-half
times as well on the government course as a tire graded
100. The relative performance of tires depends upon the
actual conditions of their use, however, and may depart
significantly from the norm due to variations in driving
habits, service practices, and differences in road charac-
teristics and climate.

Traction Grades

The Traction grades, from highest to lowest, are AA, A, B,
and C. These grades represent the tire’s ability to stop on
wet pavement, as measured under controlled conditions
on specified government test surfaces of asphalt and
concrete. A tire marked C may have poor traction perfor-
mance.

WARNING!

The traction grade assigned to this tire is based on
straight-ahead braking traction tests, and does not
include acceleration, cornering, hydroplaning, or
peak traction characteristics.

412

IF YOU NEED CONSUMER ASSISTANCE

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Chevrolet Camaro 12000 1968 Series Factory Assembly Instruction Manual preview
Camaro 12000 1968 Series
Brand: Chevrolet Pages: 455
kincrome K12071 Owner'S Assemble And Operating Manual preview
K12071
Brand: kincrome Pages: 6
ECS Electronics CR-066-BHU Manual preview
CR-066-BHU
Brand: ECS Electronics Pages: 16
DAF PACCAR PACMOBILE 20 User Manual preview
PACCAR PACMOBILE 20
Brand: DAF Pages: 18
Nuna Bugaboo turtle Instructions For Installation Manual preview
Bugaboo turtle
Brand: Nuna Pages: 17
BMW M5 2014 Service And Warranty Information preview
M5 2014
Brand: BMW Pages: 38
Icom RMK-5 Instruction Manual preview
RMK-5
Brand: Icom Pages: 20
Whispbar K481W Fitting Instructions Manual preview
K481W
Brand: Whispbar Pages: 14
Car-Interface CI-RL4-MM-NP Manual preview
CI-RL4-MM-NP
Brand: Car-Interface Pages: 23
Subaru S0A367010 Installation Instructions preview
S0A367010
Brand: Subaru Pages: 2
Acura 2011 RDX Navigation System Advanced Technology Manual preview
2011 RDX Navigation System
Brand: Acura Pages: 16
Prorack K443 Fitting Instructions Manual preview
K443
Brand: Prorack Pages: 14
Prorack K319 Fitting Instructions Manual preview
K319
Brand: Prorack Pages: 13
Intellitronix BG6003 Installation Manual preview
BG6003
Brand: Intellitronix Pages: 11
GMC 2004 Cadillac Warranty And Owner Assistance Information preview
2004 Cadillac
Brand: GMC Pages: 40
Audi A5 SPORTBACK Owner'S Manual preview
A5 SPORTBACK
Brand: Audi Pages: 313
Mazda 6 Sport Wagon Specification preview
6 Sport Wagon
Brand: Mazda Pages: 11
Autel MaxiTrip TP100 Manual preview
MaxiTrip TP100
Brand: Autel Pages: 26

Brands by name

Popular brands

Load more brands