Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 332 | Manualshive

Page: 332 / 440

background image

the instrument cluster) remains on continuously after
starting the engine of the vehicle with the discharged
battery.

8. When removing the jumper cables, reverse the above
sequence exactly. Be careful of the moving belts and fan.

WARNING!

•

You should not try to start your vehicle by pushing
or towing.

•

Do not connect the cable to the negative post of the
discharged battery. The resulting electrical spark
could cause the battery to explode.

(Continued)

WARNING! (Continued)

•

During cold weather when temperatures are be-
low the freezing point, electrolyte in a discharged
battery may freeze. Do not attempt jump-starting
because the battery could rupture or explode. The
battery temperature must be brought above the
freezing point before attempting jump-start.

FREEING A STUCK VEHICLE

If your vehicle becomes stuck in mud, sand, or snow, it
can often be moved by a rocking motion. Turn your
steering wheel right and left to clear the area around the
front wheels. Then shift back and forth between RE-
VERSE and DRIVE. Usually, the least accelerator pedal
pressure to maintain the rocking motion without spin-
ning the wheels is most effective.

330

WHAT TO DO IN EMERGENCIES

«
...
330
331
332
333
334
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Hama Pages: 2

Brand: Abarth Pages: 36

Brand: JASTEC Pages: 12

Brand: Kargo Master Pages: 5

Brand: Lincoln Pages: 424

Brand: Volkswagen Pages: 26

Brand: REVCAMUK Pages: 4

Brand: Fiat Pages: 172

Brand: Honda Pages: 6

Brand: MASCOT Pages: 12

Brand: StowAway 2 Pages: 2

Brand: TAUBENREUTHER Pages: 8

Brand: FALCON RIDGE Pages: 8

Brand: Scosche Pages: 8

Brand: RAM Pages: 496

Brand: SCC Pages: 4

HU-4421-XL-SDK01

Brand: FALCON RIDGE Pages: 5

Brand: Sanitas Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands