Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 191 | Manualshive

Page: 191 / 440

background image

RW/FF (CD MODE)

Press and hold FF (Fast Forward) and the CD player will
begin to fast forward until FF is released, or RW or
another CD button is pressed. The RW (Rewind) button
works in a similar manner.

AM or FM Button (CD MODE)

Switches the radio to the radio mode.

Notes On Playing MP3/WMA Files

The radio can play MP3/WMA files; however, acceptable
MP3/WMA file recording media and formats are limited.
When writing MP3/WMA files, pay attention to the
following restrictions.

Supported Media (Disc Types)

The MP3/WMA file recording media supported by the
radio are CDDA, CD-R, CD-RW, MP3,WMA, and
CDDA+MP3.

Supported Medium Formats (File Systems)

The medium formats supported by the radio are ISO 9660
Level 1 and Level 2 and includes the Joliet extension.
When reading discs recorded using formats other than
ISO 9660 Level 1 and Level 2, the radio may fail to read
files properly and may be unable to play the file nor-
mally. UDF and Apple HFS formats are not supported.

The radio uses the following limits for file systems:

•

Maximum number of directory levels: 8

•

Maximum number of files: 255

•

Maximum number of folders: 100

•

Maximum number of characters in file/folder names:

•

Level 1: 12 (including a separator

⬙

.

⬙

and a three-

character extension)

•

Level 2: 31 (including a separator

⬙

.

⬙

and a three-

character extension)

UNDERSTANDING YOUR INSTRUMENT PANEL

189

4

«
...
189
190
191
192
193
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Ultra Start Pages: 8

Brand: Uebler Pages: 18

Brand: Jeep Pages: 380

Brand: tams elektronik Pages: 44

Brand: Thule Pages: 8

Brand: Axxess Pages: 16

Brand: Weather Guard Pages: 8

Brand: Hollywood Racks Pages: 8

MagicComfort MSH50

Brand: Waeco Pages: 104

Brand: Front Runner Pages: 7

Brand: GMC Pages: 20

Brand: VDO Pages: 6

Brand: MeiTrack Pages: 15

Brand: Free2Move eSolutions Pages: 33

Brand: Steinhof Pages: 2

Brand: Metra Electronics Pages: 2

2011 ODYSSEY TOURING

Brand: Honda Pages: 21

Brand: RBP Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands