Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 119 | Manualshive

Page: 119 / 440

background image

WARNING!

•

Persons who are unable to feel pain to the skin
because of advanced age, chronic illness, diabetes,
spinal cord injury, medication, alcohol use, ex-
haustion, or other physical conditions must exer-
cise care when using the seat heater. It may cause
burns even at low temperatures, especially if used
for long periods.

•

Do not place anything on the seat that insulates
against heat, such as a blanket or cushion. This
may cause the seat heater to overheat.

Folding Rear Seat

The rear seatbacks can be folded forward to provide an
additional storage area. Pull on the loops shown in the
illustration to fold down either or both seatbacks. These
loops can be tucked away when not in use.

When the seatback is folded to the upright position, make
sure it is latched by strongly pulling on the top of the
seatback above the seat strap.

Rear Folding Seat

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

117

3

«
...
117
118
119
120
121
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: AAMP of America Pages: 6

Brand: Harmar Mobility Pages: 10

Brand: JASTEC Pages: 12

Brand: Calix Pages: 5

Brand: GMC Pages: 499

Brand: Kia Pages: 290

Brand: B-Speech Pages: 24

Brand: Thule Pages: 8

FIX&GO automatic

Brand: Alfa Romeo Pages: 40

Brand: A-Tach Pages: 2

Brand: Yakima Pages: 12

Brand: FALCON RIDGE Pages: 6

Brand: T-Mobile Pages: 2

Brand: Omix-Ada Pages: 6

Brand: ULTIMATE SPEED Pages: 10

Brand: Mitsubishi Pages: 362

Brand: Fiat Pages: 284

Brand: Curt Group Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands