manualshive.com logo in svg

Dodge 2009 Challenger SRT8, Owner'S Manual

The 2009 Dodge Challenger SRT8 is a powerful and iconic muscle car, built for speed and style. To fully maximize your driving experience, it's crucial to have the corresponding Owner's Manual. Download the manual for free from our website, providing insightful instructions and essential information for your vehicle.

Share
Download
background image

WARNING!

Do not attempt to push or tow your vehicle to get it
started. Unburned fuel could enter the catalytic con-
verter and once the engine has started, ignite and
damage the converter and vehicle. If the vehicle has
a discharged battery, booster cables may be used to
obtain a start from another vehicle. This type of start
can be dangerous if done improperly, so follow the
procedure carefully. See Section 6 of this manual for
jump-starting instructions.

Automatic Transmission — If Equipped

The shift lever must be in the NEUTRAL or PARK
position before you can start the engine. Apply the brakes
before shifting into any driving gear.

CAUTION!

Damage to the transmission may occur if the follow-
ing precautions are not observed:

•

Shift into PARK only after the vehicle has come to
a complete stop.

•

Shift into or out of REVERSE only after the
vehicle has come to a complete stop and the engine
is at idle speed.

•

Do not shift from REVERSE, PARK, or NEUTRAL
into any forward gear when the engine is above
idle speed.

•

Before shifting into any gear, make sure your foot
is firmly on the brake pedal.

Using Fob With Integrated Key (Tip Start)

NOTE:

Normal starting of either a cold or a warm

engine is obtained without pumping or pressing the
accelerator pedal.

244

STARTING AND OPERATING

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

AA Products X31 Instruction Manual preview
X31
Brand: AA Products Pages: 6
KAP AUDI 4G HIGHEND Manual preview
AUDI 4G HIGHEND
Brand: KAP Pages: 20
RACLET SAFARI Setup And Maintenance Manual preview
SAFARI
Brand: RACLET Pages: 48
RACLET Allegra Manual preview
Allegra
Brand: RACLET Pages: 31
RAM 2015 1500 User Manual preview
2015 1500
Brand: RAM Pages: 292
RAM Trucks 1500 User Manual preview
Trucks 1500
Brand: RAM Pages: 116
Metra Electronics 99-3030B Installation Instructions Manual preview
99-3030B
Brand: Metra Electronics Pages: 12
Halfords Exodus 360 Fitting Instructions preview
Exodus 360
Brand: Halfords Pages: 4
BMW 3-series convertible Complete Vehicle Workbook preview
3-series convertible
Brand: BMW Pages: 98
SuperATV AAB-P-RZR900-K2-001 Installation Instructions preview
AAB-P-RZR900-K2-001
Brand: SuperATV Pages: 3
Tessera4x4 SOT-1311 ROLL Installation Manual preview
SOT-1311 ROLL
Brand: Tessera4x4 Pages: 20
Whispbar K934W Fitting Instructions Manual preview
K934W
Brand: Whispbar Pages: 15
Waeco 8885100124 Operating Manual preview
8885100124
Brand: Waeco Pages: 172
VBG 56-201901 Mounting Instructions preview
56-201901
Brand: VBG Pages: 16
Ranger design 1525-NS Installation Manual preview
1525-NS
Brand: Ranger design Pages: 22
National Cycle Quantum hardcoated N30216 Assembly Instructions And Owner'S Manual preview
Quantum hardcoated N30216
Brand: National Cycle Pages: 3
Mercedes-Benz 240 D 1979 Owner'S Manual preview
240 D 1979
Brand: Mercedes-Benz Pages: 91
Gator GRM430EM User Manual preview
GRM430EM
Brand: Gator Pages: 6

Brands by name

Popular brands

Load more brands