manualshive.com logo in svg

Dodge 2009 Challenger SRT8, Owner'S Manual

The 2009 Dodge Challenger SRT8 is a powerful and iconic muscle car, built for speed and style. To fully maximize your driving experience, it's crucial to have the corresponding Owner's Manual. Download the manual for free from our website, providing insightful instructions and essential information for your vehicle.

Share
Download
background image

STARTING PROCEDURES

Before starting your vehicle, adjust your seat, adjust the
inside and outside mirrors, fasten your seat belt, and if
present, instruct all other occupants to buckle their seat
belts.

WARNING!

•

Never leave children alone in a vehicle. Leaving
unattended children in a vehicle is dangerous for a
number of reasons. A child or others could be
seriously or fatally injured. Do not leave the key in
the ignition. A child could operate power win-
dows, other controls, or move the vehicle.

•

Do not leave animals or children inside parked
vehicles in hot weather; interior heat buildup may
cause serious injury or death.

Manual Transmission — If Equipped

Apply the parking brake, place the shift lever in NEU-
TRAL and press the clutch pedal before starting vehicle.
This vehicle is equipped with a clutch interlocking igni-
tion system. It will not start unless the clutch pedal is
pressed to the floor.

Normal Starting with Integrated Key — Manual
Transmission

Normal starting of either a cold or a warm engine does
not require pumping or pressing the accelerator pedal.
Press the clutch pedal fully to the floor, and turn the
ignition switch to the START position and release when
the engine starts. If the engine fails to start within
15 seconds, turn the ignition switch to the OFF position,
wait 10 to 15 seconds, then repeat the “Normal Starting”
procedure.

STARTING AND OPERATING

243

5

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

iDataLink maestro Pr 2 Install Manual preview
maestro Pr 2
Brand: iDataLink Pages: 99
CITROEN PICASSO XSARA DESIRE 1.6 - MESUREMENT Manual preview
PICASSO XSARA DESIRE 1.6 - MESUREMENT
Brand: CITROEN Pages: 2
Mercedes-Benz 2013 C-Class Coupe Owner'S Manual preview
2013 C-Class Coupe
Brand: Mercedes-Benz Pages: 388
Standby L54 Manual preview
L54
Brand: Standby Pages: 10
PEUGEOT Partner Origin Handbook preview
Partner Origin
Brand: PEUGEOT Pages: 128
Schumacher Electric SPI6 Owner'S Manual preview
SPI6
Brand: Schumacher Electric Pages: 87
Cadillac 2009 ESCALADE ESV Owner'S Manual preview
2009 ESCALADE ESV
Brand: Cadillac Pages: 602
Vintage Air 561163 Manual preview
561163
Brand: Vintage Air Pages: 28
Kia Picanto 2015 Quick Reference Manual preview
Picanto 2015
Brand: Kia Pages: 10
Whispbar K561W Fitting Instructions Manual preview
K561W
Brand: Whispbar Pages: 15
Mercedes-Benz R-Class Owner'S Manual preview
R-Class
Brand: Mercedes-Benz Pages: 373
GMC Chevrolet Silverado 2500HD 2021 Owner'S Manual preview
Chevrolet Silverado 2500HD 2021
Brand: GMC Pages: 433
Camoplast Polaris TATOU 4S Installation Manuallines preview
Polaris TATOU 4S
Brand: Camoplast Pages: 13
Safe Fleet PRIME DESIGN VCR-TC11B Assembly Instructions Manual preview
PRIME DESIGN VCR-TC11B
Brand: Safe Fleet Pages: 12
EUFAB 12014 Manual preview
12014
Brand: EUFAB Pages: 20
Brodit Heavy Duty ProClip Installation Instructions preview
Heavy Duty ProClip
Brand: Brodit Pages: 2
Kargo Master 408TC Installation Manual preview
408TC
Brand: Kargo Master Pages: 14
VDO TRIM GAUGE Installation Instructions Manual preview
TRIM GAUGE
Brand: VDO Pages: 6

Brands by name

Popular brands

Load more brands