Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 262 | Manualshive

Page: 262 / 440

background image

When parking on a flat surface, place the shift lever in the
PARK position first, and then apply the parking brake.

When parking on a hill, it is important to set the parking
brake before placing the shift lever in PARK, otherwise
the load on the transmission locking mechanism may
make it difficult to move the shift lever out of PARK. As
an added precaution, turn the front wheels toward the
curb on a downhill grade and away from the curb on an
uphill grade.

WARNING!

Never use the PARK position as a substitute for the
parking brake. Always apply the parking brake fully
when parked to guard against vehicle movement and
possible injury or damage.

The following indicators should be used to ensure that
you have engaged the shift lever in the PARK position:

•

When shifting into PARK, move the shift lever all the
way forward and to the left until it stops and is fully
seated.

•

Look at the shift indicator display on the instrument
panel to ensure it is in the PARK position.

CAUTION!

Damage to the shifter could result if the shift lever is
moved out of PARK before the ignition is turned
from the LOCK to ON position.

REVERSE

This range is used for moving the vehicle rearward.
Always stop before moving the shift lever to REVERSE.

260

STARTING AND OPERATING

«
...
260
261
262
263
264
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Qube Pages: 19

Brand: Cadillac Pages: 32

21 COVERT Series

Brand: Code 3 Pages: 16

Brand: Mercedes-Benz Pages: 30

Car Top Duffle Bag

Brand: Rightline Gear Pages: 2

Brand: Ford Pages: 38

Brand: BURY Pages: 2

2005 P207 Explorer Sport Trac

Brand: Ford Pages: 540

Brand: Mercedes-Benz Pages: 296

Brand: Horn Tools Pages: 12

IT FITS RBO1018

Brand: RBO Pages: 36

Brand: Whispbar Pages: 14

MAGIC WATCH MWE-850-4XXL

Brand: Waeco Pages: 228

Brand: Toyota Pages: 26

Turnoverball 1020

Brand: Bowers & Wilkins Pages: 6

Brand: Truma Pages: 84

Brand: SAF-HOLLAND Pages: 22

2011 odyssey EX-L

Brand: Honda Pages: 722

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands