Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 163 | Manualshive

Page: 163 / 440

background image

If the light remains on when the parking brake has been
disengaged, and the fluid level is at the full mark on the
master cylinder reservoir, it indicates a possible brake
hydraulic system malfunction or that a problem with the
Brake Booster has been detected by the Anti-Lock Brake
System (ABS) / Electronic Stability Program (ESP) sys-
tem. In this case, the light will remain on until the
condition has been corrected. If the problem is related to
the brake booster, the ABS pump will run when applying
the brake and a brake pedal pulsation may be felt during
each stop.

The dual brake system provides a reserve braking capac-
ity in the event of a failure to a portion of the hydraulic
system. A leak in either half of the dual brake system is
indicated by the Brake Warning Light, which will turn on
when the brake fluid level in the master cylinder has
dropped below a specified level.

The light will remain on until the cause is corrected.

NOTE:

The light may flash momentarily during sharp

cornering maneuvers, which change fluid level condi-
tions. The vehicle should have service performed, and
the brake fluid level checked.

If brake failure is indicated, immediate repair is neces-
sary.

WARNING!

Driving a vehicle with the red brake light on is
dangerous. Part of the brake system may have failed.
It will take longer to stop the vehicle. You could have
an accident. Have the vehicle checked immediately.

Vehicles equipped with the Anti-Lock Brake System
(ABS), are also equipped with Electronic Brake Force
Distribution (EBD). In the event of an EBD failure, the
Brake Warning Light will turn on along with the ABS
Light. Immediate repair to the ABS system is required.

UNDERSTANDING YOUR INSTRUMENT PANEL

161

4

«
...
161
162
163
164
165
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Back View Pages: 168

Brand: Mazda Pages: 720

Brand: Subaru Pages: 99

Brand: Phonocar Pages: 6

Brand: Wilco Offroad Pages: 4

Brand: GMC Pages: 20

Brand: Hummer Pages: 502

Brand: Kuda Pages: 2

Electra 225 1965

Brand: Buick Pages: 914

Brand: Hyundai Pages: 19

Brand: RBO Pages: 15

Brand: AIS Pages: 2

Brand: v.link Pages: 12

Brand: Mercedes-Benz Pages: 296

Bluetooth Kit3 PLUS

Brand: N-Com Pages: 36

Brand: Honda Pages: 4

Brand: Pet Gear Pages: 4

Brand: Porsche Pages: 146

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands