manualshive.com logo in svg

Dodge 2009 Challenger SRT8, Owner'S Manual

The 2009 Dodge Challenger SRT8 is a powerful and iconic muscle car, built for speed and style. To fully maximize your driving experience, it's crucial to have the corresponding Owner's Manual. Download the manual for free from our website, providing insightful instructions and essential information for your vehicle.

Share
Download
background image

until an upshift or downshift is chosen. When you wish
to disengage Autostick

威

, hold the shift lever to the right

for at least two seconds. The transmission will now
operate automatically, shifting between the five available
gears.

Autostick

姞

General Information

•

You can start out in first or second gear. The system
will ignore attempts to upshift at too low of a vehicle
speed or downshift at too high of a vehicle speed..

•

The transmission will automatically downshift to 1st
gear when coming to a stop.

•

Starting out in second gear is helpful in snowy or icy
conditions.

•

Avoid using speed control when Autostick

威

is en-

gaged.

•

The transmission will automatically shift up when
maximum engine speed is reached while Autostick

威

is

engaged.

•

Transmission shifting will be more sharper when
Autostick

威

is engaged.

DRIVING ON SLIPPERY SURFACES

Acceleration

Rapid acceleration on snow covered, wet, or other slip-
pery surfaces may cause the rear wheels to pull errati-
cally to the right or left. This phenomenon occurs when
there is a difference in the surface traction under the rear
(driving) wheels.

264

STARTING AND OPERATING

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

KC HiLiTES C Series Wiring Diagram preview
C Series
Brand: KC HiLiTES Pages: 4
iDataLink maestro Rr Install Manual preview
maestro Rr
Brand: iDataLink Pages: 106
Kuda-Phonebase 055040 Installation Instruction preview
055040
Brand: Kuda-Phonebase Pages: 3
Toyota YARIS LIFTBACK 2009 Quick Reference Manual preview
YARIS LIFTBACK 2009
Brand: Toyota Pages: 13
Westfalia 316 145 Manual preview
316 145
Brand: Westfalia Pages: 71
Yakima StickUp Installation Instructions Manual preview
StickUp
Brand: Yakima Pages: 21
Subaru 2007 Impreza Brochure & Specs preview
2007 Impreza
Brand: Subaru Pages: 21
Chevrolet 2014 TRAX Owner'S Manual preview
2014 TRAX
Brand: Chevrolet Pages: 412
Tabernus Peram Hatch-bag Luggage System Installation Instructions Manual preview
Hatch-bag Luggage System
Brand: Tabernus Peram Pages: 10
Mynew Portable Car Umbrella User Manual preview
Portable Car Umbrella
Brand: Mynew Pages: 5
QA1 GS501 Installation Instructions preview
GS501
Brand: QA1 Pages: 3
RAM 1500 CLASSIC 2020 Owner'S Manual preview
1500 CLASSIC 2020
Brand: RAM Pages: 360
Phonocell 6/821 Mounting Instructions preview
6/821
Brand: Phonocell Pages: 8
Ford TRANSIT 2015 Quick Reference Manual preview
TRANSIT 2015
Brand: Ford Pages: 8
Pyle PLPSC8 User Manual preview
PLPSC8
Brand: Pyle Pages: 14
VDO ELECTRONIC SPEEDOMETER 1323 Datasheet preview
ELECTRONIC SPEEDOMETER 1323
Brand: VDO Pages: 2
Kia MOHAVE 2014 Owner'S Manual preview
MOHAVE 2014
Brand: Kia Pages: 417
Automotive Data Solutions BLADE-AL-TL5-EN Install Manual preview
BLADE-AL-TL5-EN
Brand: Automotive Data Solutions Pages: 27

Brands by name

Popular brands

Load more brands