Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 315 | Manualshive

Page: 315 / 440

background image

•

Guard against carbon monoxide with proper mainte-
nance. Have the exhaust system inspected every time
the vehicle is raised. Have any abnormal conditions
repaired promptly. Until repaired, drive with all side
windows fully open.

•

Keep the trunk/liftgate closed when driving your
vehicle to prevent carbon monoxide and other poison-
ous exhaust gases from entering the vehicle.

ADDING FUEL

Fuel Filler Cap (Gas Cap)

The gas cap is located behind the fuel filler door on the
left side of the vehicle. Use a finger to pull open the door.
If the gas cap is lost or damaged, be sure the replacement
cap is for use with this vehicle.

NOTE:

When removing the fuel filler cap, lay the cap

tether in the hook, located on the fuel filler door.

Fuel Fill Cap

STARTING AND OPERATING

313

5

«
...
313
314
315
316
317
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Lancia Pages: 276

Brand: T-Tech Pages: 38

Brand: Jetter Pages: 4

Brand: K&K Pages: 8

Brand: K&K Pages: 20

Brand: K&K Pages: 6

Brand: K&K Pages: 3

Brand: K&K Pages: 3

Brand: Aries Pages: 3

Brand: Yakima Pages: 21

Brand: BMW Pages: 21

Brand: Thule Pages: 2

Brand: Hyundai Pages: 11

Brand: rough country Pages: 4

Brand: Bestop Pages: 4

84 61 0 028 926

Brand: BMW Pages: 13

Brand: Roadtrek Pages: 61

Brand: Brodit Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands