Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 158 | Manualshive

Page: 158 / 440

background image

7. Electronic Throttle Control (ETC) Warning Light

This light will turn on briefly as a bulb check
when the ignition switch is turned ON. This
light will also turn on while the engine is
running if there is a problem with the Elec-

tronic Throttle Control (ETC) system.

If the light comes on while the engine is running, safely
bring the vehicle to a complete stop as soon as possible,
place the shift lever in PARK, and cycle the ignition key.
The light should turn off. If the light remains lit with the
engine running, your vehicle will usually be drivable.
However, see an authorized dealer for service as soon as
possible.

If the light is flashing when the engine is running,
immediate service is required. In this case, you may
experience reduced performance, an elevated/rough idle
or engine stall, and your vehicle may require towing.

Also, have the system checked by an authorized dealer if
the light does not come on during starting.

8. Temperature Gauge

The temperature gauge shows engine coolant tempera-
ture. Any reading within the normal range indicates that
the engine cooling system is operating satisfactorily.

The gauge pointer will likely indicate a higher tempera-
ture when driving in hot weather, up mountain grades,
or when towing a trailer. It should not be allowed to
exceed the upper limits of the normal operating range.

156

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
156
157
158
159
160
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Kargo Master Pages: 6

Brand: Xblitz Pages: 16

Brand: Barker Pages: 2

Brand: Mazda Pages: 527

2008 Escalade EXT

Brand: Cadillac Pages: 496

Brand: Yakima Pages: 12

Brand: ACV Pages: 2

Brand: Atera Pages: 3

Brand: Black Horse Pages: 5

Brand: BrandMotion Pages: 6

INDICA eV2 XETA CNG

Brand: TATA Motors Pages: 24

Brand: PAC Pages: 5

Brand: Percon Pages: 49

Brand: Opel Pages: 44

Brand: Setma Pages: 16

Brand: Raider Pages: 2

Brand: Harbor Freight Tools Pages: 8

Brand: Kuda Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands