Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 395

Page: 395 / 440

60,000 Miles (100,000 km) or 60 Months Maintenance Service
Schedule

❏

Change the engine oil and engine oil filter.

❏

Rotate tires.

❏

Replace the engine air cleaner filter.

❏

Replace the air conditioning filter.

❏

Inspect the brake linings, and replace if necessary.

❏

Adjust parking brake on vehicles equipped with four-wheel disc brakes.

❏

Inspect the manual transmission fluid (if equipped), add as necessary.

❏

Change the automatic transmission fluid and filter if using your vehicle for any of the
following: police, taxi, fleet, or frequent trailer towing.

❏

Flush and replace the engine coolant at 60 months if not done at 102,000 miles
(170 000 km).

Odometer Reading

Date

Repair Order #

Dealer Code

Signature Authorized Chrysler Dealer

66,000 Miles (110,000 km) or
66 Months Maintenance
Service Schedule

❏

Change the engine oil and engine oil
filter.

❏

Rotate tires.

Odometer Reading

Date

Repair Order #

Dealer Code

Signature Authorized Chrysler Dealer

MAINTENANCE SCHEDULES

393

T
E

N
A
N
C

S
C
H
E
D
U
L
E
S

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Search results

Summary of Contents for 2009 Challenger SRT8

Reviews:

Related manuals for 2009 Challenger SRT8

Brands by name

Popular brands

Dodge 2009 Challenger SRT8, Owner'S Manual

Search results

Summary of Contents for 2009 Challenger SRT8

Reviews:

Related manuals for 2009 Challenger SRT8

Brands by name

Popular brands