Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 322 | Manualshive

Page: 322 / 440

background image

HAZARD WARNING FLASHER

The Hazard Warning flasher switch is located in the
switch bank near the bottom center of the instrument
panel.

Press the switch to turn on the Hazard Warning
flasher. When the switch is activated, all directional
turn signals will flash on and off to warn oncoming

traffic of an emergency. Press the switch a second time to
turn off the Hazard Warning flasher.

This is an emergency warning system and it should not
be used when the vehicle is in motion. Use it when your
vehicle is disabled and it is creating a safety hazard for
other motorists.

When you must leave the vehicle to seek assistance, the
Hazard Warning flasher will continue to operate even
though the ignition switch is in the LOCK position.

NOTE:

With extended use, the Hazard Warning flasher

may wear down your battery.

IF YOUR ENGINE OVERHEATS

In any of the following situations, you can reduce the
potential for overheating by taking the appropriate ac-
tion.

•

On the highways — slow down.

•

In city traffic — while stopped, put transmission in
NEUTRAL, but do not increase engine idle speed.

320

WHAT TO DO IN EMERGENCIES

«
...
320
321
322
323
324
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Suzuki Pages: 16

Brand: Uebler Pages: 18

Brand: NavLinkz Pages: 4

Brand: Chevrolet Pages: 494

1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28

Brand: Havis-Shields Pages: 3

Autostacker PL-6SR

Brand: BendPak Pages: 104

Impala Limited 2014

Brand: Chevrolet Pages: 356

Brand: Fab Fours Pages: 13

Brand: Jaeger Pages: 13

Brand: v.link Pages: 12

2011 SRX CROSSOVER

Brand: Cadillac Pages: 416

Brand: TIE DOWN Pages: 2

Brand: Gator Pages: 6

Brand: F.lli Menabo Pages: 16

Brand: S&B Filters Pages: 4

Brand: Mazda Pages: 3

Brand: Cadillac Pages: 438

Brand: EUFAB Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands